6MBP20XRHA065-50
IGBT Modules
Control circuit
●
T vj=25°C,V CC=15V unless otherwise specified
Item
Supply current of P-side
pre-driver (per one unit)
Supply current of N-side
pre-driver
Symbol
Conditions
Switching frequency (f SW) = 0~15kHz
T C = -20~125°C
Min. Typ. Max. Units
-
-
8
mA
Iccp
-
-
21
mA
Iccn
V inth(on)
V inth(off)
1.2
1.5
1.4
1.7
1.6
1.9
V
V
Input signal threshold voltage
ON
OFF
V in-GND
Protection circuit
●
T vj=25°C,V CC=15V unless otherwise specified
Item
Symbol
Conditions
Min. Typ. Max. Units
T vj=150°C
30
-
-
-
-
-
A
A
μs
μs
°C
Over current
protection level
Over current protection delay time
Short circuit protection delay time
IGBT chips over heating
Inverter
Brake
IOC
-
4.0
2.0
-
-
-
-
-
t dOC
t dSC
T vj=150°C
T vj=150°C
Surface of IGBT Chips
175
T jOH
protection temperature level
°C
V
V
ms
ms
ms
V
T jH
V UV
V H
t ALM(OC)
t ALM(UV)
t ALM(TjOH)
V ALMH
R ALM
-
20
-
-
Over heating protection hysteresis
Under voltage protection level
Under voltage protection hysteresis
11.0
0.2
1.0
3.5
7.0
14.5
960
12.5
-
0.5
2.0
4.0
8.0
-
2.4
4.5
9.0
15.0
1570
ALM-GND
T C=-20~125°C
V
cc≧10V
Alarm signal hold time
Alarm signal voltage
Resistance for current limit
ALM-GND, without protection
-
Ω
Thermal resistance characteristics (T C = 25℃)
■
Item
Symbol
Min. Typ. Max. Units
K/W
R th(j-c)
Inverter
RC-IGBT
-
-
1.21
Thermal resistance
junction to case
*12
K/W
K/W
K/W
K/W
R th(j-c)Q
R th(j-c)D
R th(c-s)
IGBT
FWD
-
-
-
-
-
-
-
-
Brake
0.05
Thermal resistance case to heat sink *13
*12: For 1 device ,the measurement point of the case is just under the chip.
*13: This is the value which is defined mounting on the additional heat sink with 1 W/(m·K) thermal grease.
Noise immunity (V DC=300V, V CC=15V)
■
Item
Conditions
Min. Typ. Max. Units
Common mode
rectangular noise
Pulse width 1μs,polarity ±,10min.
Judge:no over-current, no miss operating
±2.0
-
-
kV
Recommended operating conditions
■
Item
Symbol
V DC
V CC
f SW
t dead
-
Min. Typ. Max. Units
-
-
400
V
V
DC bus voltage
13.5 15.0 16.5
Power supply voltage of pre-driver
Switching frequency of IPM
Arm short through blocking time for IPM's input signal *14
Screw torque (M4)
-
-
-
-
20.0 kHz
1.5
1.3
-
μs
1.7
Nm
t dead = t off - t d(on)
*14:
FM6M1981b
2023/03
3