5秒后页面跳转
5V40501DCG8 PDF预览

5V40501DCG8

更新时间: 2024-02-16 03:08:44
品牌 Logo 应用领域
艾迪悌 - IDT 晶体时钟发生器微控制器和处理器外围集成电路光电二极管
页数 文件大小 规格书
9页 221K
描述
LOCO™ PLL CLOCK MULTIPLIER

5V40501DCG8 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Obsolete零件包装代码:SOIC
包装说明:0.150 INCH, ROHS COMPLIANT, SOIC-8针数:8
Reach Compliance Code:unknownECCN代码:EAR99
HTS代码:8542.39.00.01风险等级:5.26
Is Samacsys:NJESD-30 代码:R-PDSO-G8
JESD-609代码:e3长度:4.9 mm
湿度敏感等级:1端子数量:8
最高工作温度:70 °C最低工作温度:
最大输出时钟频率:100 MHz封装主体材料:PLASTIC/EPOXY
封装代码:SOP封装等效代码:SOP8,.25
封装形状:RECTANGULAR封装形式:SMALL OUTLINE
峰值回流温度(摄氏度):260电源:3.3 V
主时钟/晶体标称频率:50 MHz认证状态:Not Qualified
座面最大高度:1.75 mm子类别:Clock Generators
最大供电电压:3.465 V最小供电电压:3.135 V
标称供电电压:3.3 V表面贴装:YES
技术:CMOS温度等级:COMMERCIAL
端子面层:Matte Tin (Sn) - annealed端子形式:GULL WING
端子节距:1.27 mm端子位置:DUAL
处于峰值回流温度下的最长时间:30宽度:3.9 mm
uPs/uCs/外围集成电路类型:CLOCK GENERATOR, OTHERBase Number Matches:1

5V40501DCG8 数据手册

 浏览型号5V40501DCG8的Datasheet PDF文件第1页浏览型号5V40501DCG8的Datasheet PDF文件第2页浏览型号5V40501DCG8的Datasheet PDF文件第4页浏览型号5V40501DCG8的Datasheet PDF文件第5页浏览型号5V40501DCG8的Datasheet PDF文件第6页浏览型号5V40501DCG8的Datasheet PDF文件第7页 
IDT5V40501  
LOCO™ PLL CLOCK MULTIPLIER  
CLOCK MULTIPLIER  
Crystal Load Capacitors  
External Components  
The total on-chip capacitance is approximately 12 pF. A  
parallel resonant, fundamental mode crystal should be  
used. The device crystal connections should include pads  
for small capacitors from X1 to ground and from X2 to  
ground. These capacitors are used to adjust the stray  
capacitance of the board to match the nominally required  
crystal load capacitance. Because load capacitance can  
only be increased in this trimming process, it is important to  
keep stray capacitance to a minimum by using very short  
PCB traces (and no vias) between the crystal and device.  
Crystal capacitors, if needed, must be connected from each  
of the pins X1 and X2 to ground.  
Decoupling Capacitor  
As with any high-performance mixed-signal IC, the  
IDT5V40501 must be isolated from system power supply  
noise to perform optimally.  
A decoupling capacitor of 0.01µF must be connected  
between VDD and the GND. It must be connected close to  
the IDT5V40501 to minimize lead inductance. No external  
power supply filtering is required for the IDT5V40501.  
Series Termination Resistor  
A 33terminating resistor can be used next to the CLK pin  
for trace lengths over one inch.  
The value (in pF) of these crystal caps should equal (C -12  
L
pF)*2. In this equation, C = crystal load capacitance in pF.  
L
Example: For a crystal with a 16 pF load capacitance, each  
crystal capacitor would be 8 pF [(16-12) x 2 = 8].  
Absolute Maximum Ratings  
Stresses above the ratings listed below can cause permanent damage to the IDT5V40501. These ratings, which  
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at  
these or any other conditions above those indicated in the operational sections of the specifications is not implied.  
Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical  
parameters are guaranteed only over the recommended operating temperature range.  
Item  
Rating  
Supply Voltage, VDD  
All Inputs and Outputs  
7 V  
-0.5 V to VDD+0.5 V  
-40 to +85° C  
-65 to +150° C  
260°C  
Ambient Operating Temperature  
Storage Temperature  
Soldering Temperature  
Recommended Operation Conditions  
Parameter  
Min.  
Typ.  
Max.  
+70  
Units  
° C  
Ambient Operating Temperature (commercial)  
Ambient Operating Temperature (industrial)  
Power Supply Voltage (measured in respect to GND)  
0
-40  
85  
° C  
+3.135  
3.3  
+3.465  
V
IDT™ LOCO™ PLL CLOCK MULTIPLIER  
3
IDT5V40501  
REV C 102808  

与5V40501DCG8相关器件

型号 品牌 描述 获取价格 数据表
5V40501DCGI IDT LOCO™ PLL CLOCK MULTIPLIER

获取价格

5V40501DCGI8 IDT LOCO™ PLL CLOCK MULTIPLIER

获取价格

5V40501DVG IDT LOCO™ PLL CLOCK MULTIPLIER

获取价格

5V40501DVG8 IDT LOCO™ PLL CLOCK MULTIPLIER

获取价格

5V40501DVGI IDT LOCO™ PLL CLOCK MULTIPLIER

获取价格

5V40501DVGI8 IDT LOCO™ PLL CLOCK MULTIPLIER

获取价格