1. SCOPE
1.1 Scope. This drawing describes device requirements for class B microcircuits in accordance with 1.2.1 of MIL-STD-883,
"Provisions for the use of MIL-STD-883 in conjunction with compliant non-JAN devices".
1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example:
5962-89710
01
X
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type
Generic number
Circuit function
01
02
ADG526A
ADG527A
CMOS 16-channel multiplexer latched
CMOS 8-channel multiplexer latched
1.2.2 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
Dual-in-line
X
3
GDIP1-T28 or CDIP2-T28
CQCC1-N28
28
28
Square leadless chip carrier
1.2.3 Lead finish. The lead finish shall be as specified in MIL-M-38510. Finish letter "X" shall not be marked on the microcircuit
or its packaging. The "X" designation is for use in specifications when lead finishes A, B, and C are considered acceptable and
interchangeable without preference.
1.3 Absolute maximum ratings.
Supply voltage (V ) to V
DD
SS
. . . . . . .4.4. .V.d. c. . . . . . . . . . . . . . . . . . .
Supply voltage (V ) to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 V dc
DD
V
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -25 V dc
SS
Analog inputs: 1/
Voltage at S or D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
-2.0 V dc to V
+2.0 V dc or
SS
DD
20 mA, whichever occurs first
20 mA
Continuous current, S or D
Pulsed current, S or D (1.0 ms duration, 10% duty cycle) . . . . . . . 40 mA
DC input voltages 1/ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V -4.0 V dc to V
+4.0 V dc or
20 mA, whichever occurs first
SS DD
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65 C to +150 C
Lead temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . . . . . . +300 C
Power dissipation to +75 C (P ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470 mW 2/
D
Thermal resistance, junction-to-case (
):
JC
Cases X and 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See MIL-STD-1835
Junction temperature (T ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175 C
J
1.4 Recommended operating conditions.
Supply voltage to ground (V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -15 V dc
SS
Supply voltage to ground (V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . +15 V dc
DD
Ambient operating temperature range (T ) . . . . . . . . . . . . . . . . . . . . -55 C to +125 C
A
1/ Overvoltage at A, EN, WR, RS, S, or D will be clamped by diodes. Current should be limited to the maximum rating above.
2/ Derate above T = +75 C at 6.0 mW/ C.
A
SIZE
STANDARDIZED
MILITARY DRAWING
5962-89710
A
DEFENSE ELECTRONICS SUPPLY CENTER
DAYTON, OHIO 45444
REVISION LEVEL
B
SHEET
2
DESC FORM 193A
JUL 91