3M™ Four-Wall Header
.100" × .100" Latch/Ejector, Straight and RightAngle
3000 Series
Table 1
Dimensions
B
Inch
3M Part
Number
Polarizing
Notches
(mm)
Pin Qty
A
C
D
Tolerance Unless Noted
06
08
10
14
16
20
24
26
30
34
40
50
60
64
3869
3889
3793
3314
3408
3428
3627
3429
3440
3431
3432
3433
3372
3764
1.065 (27.05)
1.165 (29.59)
1.265 (32.13)
1.465 (37.21)
1.565 (39.75)
1.765 (44.83)
1.965 (49.91)
2.065 (52.45)
2.265 (57.53)
2.465 (62.61)
2.765 (70.23)
3.265 (82.93)
3.765 (95.63)
3.965 (100.71)
0.905 (22.99)
1.005 (25.53)
1.105 (28.04)
1.305 (33.12)
1.405 (35.66)
1.605 (40.74)
1.805 (45.82)
1.905 (48.36)
2.105 (53.44)
2.305 (58.52)
2.605 (66.14)
3.105 (78.84)
3.605 (91.54)
3.805 (96.62)
0.665 (16.89)
0.765 (19.43)
0.865 (21.97)
1.065 (27.05)
1.165 (29.59)
1.365 (34.67)
1.565 (39.75)
1.665 (42.29)
1.865 (47.37)
2.065 (52.45)
2.365 (60.07)
2.865 (72.77)
3.365 (85.47)
3.565 (90.55)
0.505 (12.83)
0.605 (15.37)
0.705 (17.91)
0.905 (22.99)
1.005 (25.53)
1.205 (30.61)
1.405 (35.69)
1.505 (38.23)
1.705 (43.31)
1.905 (48.39)
2.205 (56.01)
2.705 (68.71)
3.205 (81.41)
3.405 (86.49)
B*
.00
.000
.0
B*
± .005
± .01
± .1
Inch
BC
BC
[ ] Dimensions for
Reference only
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
ABC
* Available without center notch B. Contact 3M.
Table 2
3M Part
Number Suffix
Contact Tail
Dim E
Pin Cross Section
Dim G
-5XX2
Solder Tail for
.062 (1.57)
Thick PC Board
Dim F
.0245 ± .0005
(0.622)
Diagonals
.028 ± .001
(0.71)
Corner Radii
.0075 Ref
(0.191)
.112 ± .010
(2.84)
0.035 ± .003
(0.89) (See Note 3)
-6XX2
-5X03
Solder Tail for 0.94
(2.39) to .125 (3.18)
Thick PC Board
.155 ± .010
(3.94)
.0245 ± .0005
(0.622)
.028 ± .001
(0.71)
.0075 Ref
(0.191)
0.035 ± .003 (0.89)
-6X03
or ø.116
[2.95]
ø.106
[2.69]
or
ø.106
[2.69]
ø.116
[2.95]
.41
[10.4]
(See Note 2)
(See Note 2)
.300
[7.62]
Side to Side Stackability
Max to Edge of PCB
for Daisy Chain
Dim G
Dim G
"Y"
C
L
C
L
“Y”
Position 1
.029
Position 1
[0.74]
.060
[1.52]
.100 .003
[2.54]
.100 .003
[2.54]
.100 .003
[2.54]
.232
[5.89]
.352
[8.94]
.100 .003
[2.54]
C
B
Recommended Mounting Hole Pattern
Recommended Mounting Hole Pattern
(Right Angle)
(Straight)
Notes: 1. Notches A & C will accomodate 3M Polarizing Keys (3M Part #3518 or #N3518).
2. Mounting hardware: From solder side of pc board use #4-24 thread cutting screw (3M Part # 3341-5) and .116 [2.95] dia mounting hole. For right angle version only, #2-56 bolt and nut (3M
Part # 3341-6) with .106 [2.69] dia mounting hole may be used. See illustrations on page 4.
3.The recommended PCB hole size for the kinked tail positions on the .112 solder tail connector is .035 .002. See page 4 for kink position details (K2 version).
4. Contact your 3M sales representative for custom requirements.
X3XXX-XXXXXX
Plating
Ordering Information
RB = 30 μ” [ 0.76 μm ] Gold and 200 μ” [ 5.08 μm ] Matte Tin
N = High Temp Black (PCT)/(RB Plating Req’d)
(App. E1 & C1 Apply)
Blank = Std. Temp Gray (PBT) /(Blank or UB Pltg. Req’d.)
Blank or UB = 30 μ” (0.76 μm ] Gold and 200 μ” [ 5.08 μm ]
Tin Lead (App. E3 & C2 Apply)
3M Part Number
(See Table 1)
Latch/Ejector System
Tail
0 = No Latch/Ejector installed
2 = Short Roll Pin Latch/Ejectors
3 = Long, Roll Pin Latch/Ejectors
5 = Short, Snap-In Latch/Ejectors
6 = Long, Snap-In Latch/Ejectors
02 = for .062 [1.57] thick board
03 = for .094 to .125 [2.39 to 3.18] thick board
K2 = kinked for .062 [1.57] thick board
Pin Configuration
5 = Right Angle Solder Tails
6 = Straight Solder Tails
TS-0772-P
Sheet 3 of 4
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com