GENERAL DATA — 500 mW DO-35 GLASS
Low Voltage Avalanche Passivated
Silicon Oxide Zener Regulator Diodes
Same as 1N5520B through 1N5530B except low noise test
spec omitted.
• Low Maximum Regulation Factor
• Low Zener Impedance
• Low Leakage Current
ELECTRICAL CHARACTERISTICS (T = 25°C unless otherwise specified. Based on dc measurements at thermal equilibrium;
A
ELECTRICAL CHARACTERISTICS V = 1.1 Max @ I = 200 mA for all types.)
F
F
Nominal
Zener
Voltage
Maximum
DC Zener
Current
Max Reverse Leakage Current
Max Zener
Impedance
@ I
Ohms
(Note 3)
Regulation
Factor
Low
Test
Current
V
Z
V
@ I
Volts
I
R
I
Motorola
Type No.
(Note 1)
Z
∆V
Volts
Current
Z
ZT
ZM
ZT
ZT
Z
µAdc
mAdc
I
I
ZT
ZL
(Note 2)
(Note 4)
(Note 5)
mAdc
V
R
– Volts
(Note 6)
mAdc
MZ5520B
MZ5521B
MZ5522B
MZ5523B
MZ5524B
3.9
4.3
4.7
5.1
5.6
20
20
10
5
22
18
22
26
30
1
3
2
2
2
1
1.5
2
2.5
3.5
98
88
81
75
68
0.85
0.75
0.6
0.65
0.3
2.0
2.0
1.0
0.25
0.25
3
MZ5525B
MZ5526B
MZ5527B
MZ5528B
MZ5529B
MZ5530B
6.2
6.8
7.5
8.2
9.1
10
1
1
1
1
1
1
30
30
35
40
45
60
1
1
0.5
0.5
0.1
0.05
5
61
56
51
46
42
38
0.2
0.1
0.05
0.05
0.05
0.1
0.01
0.01
0.01
0.01
0.01
0.01
6.2
6.8
7.5
8.2
9.1
NOTE 1. TOLERANCE AND VOLTAGE DESIGNATION
NOTE 5. MAXIMUM REGULATOR CURRENT (I
)
ZM
The maximum current shown is based on the maximum voltage of a ±5% type unit, therefore,
it applies only to the “B” suffix device. The actual I for any device may not exceed the value
The “B” suffix type numbers listed are ±5% tolerance of nominal V
.
Z
ZM
of 400 milliwatts divided by the actual V of the device.
NOTE 2. ZENER VOLTAGE (V ) MEASUREMENT
Z
Nominal zener voltage is measured with the device junction in thermal equilibrium with ambi-
Z
ent temperature of 25°C.
NOTE 6. MAXIMUM REGULATION FACTOR (∆V
)
Z
∆V is the maximum difference between V at I and V at I measured with the device
junction in thermal equilibrium.
NOTE 3. ZENER IMPEDANCE (Z ) DERIVATION
Z
Z
ZT
Z
ZL
Z
The zener impedance is derived from the 60 Hz ac voltage, which results when an ac current
having an rms value equal to 10% of the dc zener current (I ) is superimposed on I
ZT
.
ZT
NOTE 7. SPECIAL SELECTORS AVAILABLE INCLUDE:
NOTE 4. REVERSE LEAKAGE CURRENT I
R
Reverse leakage currents are guaranteed and are measured at V as shown on the table.
R
A) Tighter voltage tolerances. Contact your nearest Motorola representative for more infor-
mation.
Motorola TVS/Zener Device Data
500 mW DO-35 Glass Data Sheet
6-113