Datasheet > 13191

13191

更新时间： 2022-04-23 23:00:11

品牌	Logo	应用领域
飞思卡尔 - FREESCALE		ISM频段
页数	文件大小	规格书
24页	375K
描述
2.4 GHz ISM Band Low Power Transceiver

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

13191 数据手册

User must be sure manufacturer specifications apply to the desired package.

A wider frequency tolerance may acceptable if application uses trimming at production final test.

A wider frequency stability may be acceptable if application uses trimming at production final test.

A wider aging tolerance may be acceptable if application uses trimming at production final test.

Higher ESR may be acceptable with lower load capacitance.

Lower load capacitance can allow higher ESR and is better for low temperature operation in Doze mode.

8.4

Low Power Considerations

•

Program and use the modem IO pins properly for low power operation

— All unused modem GPIOx signals must be used one of 2 ways:

– If the Off mode is to be used as a long term low power mode, unused GPIO should be tied

to ground. The default GPIO mode is an input and there will be no conflict.

– If only Hibernate and/or Doze modes are used as long term low power modes, the GPIO

should programmed as outputs in the low state.

— When modem GPIO are used as outputs:

– Pullup resistors should be provided (can be provided by the MCU IO pin if tied to the MCU)

if the modem Off condition is to be used as a long term low power mode.

– During Hibernate and/or Doze modes, the GPIO will retain its programmed output state.

— If the modem GPIO is used as an input, the GPIO should be driven by its source during all low

power modes or a pullup resistor should be provided.

— Digital outputs IRQ, MISO, and CLKO:

– MISO - is always an output. During Hibernate, Doze, and active modes, the default

condition is for the MISO output to go to tristate when CE is de-asserted, and this can cause

a problem with the MCU because one of its inputs can float. Program Control_B Register

07, Bit 11, miso_hiz_en = 0 so that MISO is driven low when CE is de-asserted. As a result,

MISO will not float when Doze or Hibernate Mode is enabled.

– IRQ - is an open drain output (OD) and should always have a pullup resistor (typically

provided by the MCU IO). IRQ acts as the interrupt request output.

NOTE

It is good practice to have the IRQ interrupt input to the MCU disabled

during the hardware reset to the modem. After releasing the modem

hardware reset, the interrupt request input to the MCU can then be enabled

to await the IRQ that signifies the modem is ready and in Idle mode; this can

prevent a possible extraneous false interrupt request.

– CLKO - is always an output. During Hibernate CLKO retains its output state, but does not

toggle. During Doze, CLKO may toggle depending on whether it is being used.

•

If the MCU is also going to be used in low power modes, be sure that all unused IO are programmed

properly for low power operation (typically best case is as outputs in the low state). The MC13191

is commonly used with the Freescale MC9S08GT/GB 8-bit devices. For these MCUs:

— Use only STOP2 and STOP3 modes (not STOP1) with these devices where the GPIO states are

retained. The MCU must retain control of the MC13191 IO during low power operation.

MC13191 Technical Data, Rev. 1.6

Freescale Semiconductor

1...17 18 192021 22 23 24

中文翻译

下载PDF

与13191相关器件

型号	品牌	获取价格	描述	数据表
131-91028	AMPHENOL	获取价格	RF Connector Adapter, APC-7-SMA, Cable Mount, Female-Female, Plug-jack
131-91046	AMPHENOL	获取价格	RF Connector Adapter, APC-7-APC-3.5, Female, Jack-jack
1319-13-D3-60-010	ECS	获取价格	Card Edge Connector
13192	FREESCALE	获取价格	2.4 GHz Low Power Transceiver for the IEEE 802.15.4 Standard
1319-21-D1-40-010	ECS	获取价格	Card Edge Connector
1319-22-D2-60-010	ECS	获取价格	Card Edge Connector
1319-25-D2-60-010	ECS	获取价格	Card Edge Connector
1319260000	WEIDMULLER	获取价格	SAKT 4/LT SAKT 4/DU SAKT 1/DU SAKT 1/QT
1319-35-D2-60-010	ECS	获取价格	Card Edge Connector
1319-35-D3-30-010	ECS	获取价格	Card Edge Connector

与13191相关文章

晶闸管阳极与阴极之间加电压时控制极的电流流动分析
2024-06-05

10
探究MOS管沟道夹断后载流子传输机制及其电路设计影响
2024-06-05

9
光敏电阻的工作原理、作用及检测方法
2024-06-05

8
ENC28J60以太网控制器全面解析：特性、应用、引脚说明
2024-06-05

6

产品中心

服务支持

精选活动

关于我们

帮助中心

13191

13191 数据手册

与13191相关器件

与13191相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

13191

13191 数据手册

与13191相关器件

与13191相关文章

您还可以找

您在本页遇到什么问题？