Datasheet > 1151

1151

更新时间： 2024-11-18 06:25:59

品牌	Logo	应用领域
SYSTEMSENSOR		/
页数	文件大小	规格书
4页	87K
描述
Low Profile Ionization Plug-in Smoke Detectors

阅读下载

中文翻译

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

1151 数据手册

INSTALLATION AND MAINTENANCE INSTRUCTIONS

1151 Low Profile Ionization

Plug-in Smoke Detectors

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

Specifications

Size

Height:

Diameter:

Weight:

1.7 inches (43 mm)

4.0 inches (102 mm)

3.6 oz (102 g)

Operating Temperature Range:

–10°C to 60°C (14°F to 140°F)

NOTE: Do not install in locations where normal ambient temperature range extends

beyond 0°C to 49°C (32°F to 120°F)

Operating Humidity Range:

Latching Alarm:

10% to 93% Relative Humidity, Noncondensing

Reset by momentary power interruption

Before Installing

Base Selection and Wiring Guide

Please thoroughly read the System Sensor manual A05- Refer to the installation instructions for the plug-in detector

1003, Applications Guide for System Smoke Detectors, bases for wiring instructions. System Sensor has available a

which provides detailed information on detector spacing, variety of detector bases for this smoke detector, including

placement, zoning, wiring, and special applications. Copies 2-wire applications with and without relays and/or current

of this manual are available from System Sensor.

limiting resistors, 4-wire and 120 VAC applications.

NOTICE: This manual should be left with the owner/user All bases are provided with screw terminals for power,

of this equipment.

ground, remote annunciator connections, and relay contact

connections, if applicable. The electrical ratings for each

IMPORTANT: The detector used with this base must be detector-base combination are also included in the base

tested and maintained regularly following NFPA 72 require- installation instructions.

ments. The detector used with this base should be cleaned

at least once a year.

Installation

NOTE: All wiring must conform to applicable local codes,

ordinances, and regulations.

General Description

Model 1151 ionization detector uses state-of-the-art sens- NOTE: Verify that all detector bases are installed, that the

ing chambers. This detector is designed to provide open

area protection, and to be used with compatible UL-listed

control panels only. The capability of plugging this detector

into a variety of special bases makes it more versatile than

equivalent direct-wired models.

initiating-device circuits have been tested, and that

the wiring is correct.

WARNING

Remove power from initiating device circuits before install-

ing detectors.

Two LEDs on each detector light to provide a local 360° vis-

ible alarm indication. Remote LED annunciator capability

is available as an optional accessory. This detector also has

the latching alarm feature. The alarm can be reset only by

a momentary power interruption. For testing, this detector

has an internal magnetically activated reed switch.

1. Install Detectors:

a. Place the detector into the detector base.

b. Rotate the detector clockwise until the detector drops

into place.

c. Continue rotating the detector clockwise to lock it in

place.

Spacing

2. Tamper-Resistance: The detector bases include a feature

that, when activated, prevents removal of the detector

without the use of a tool. See the installation instruc-

tion manual of the detector base for details in using this

feature.

Spacing of 30 ft. on a smooth ceiling as per NFPA 72.

Where conditions or response requirements vary, other

spacing may apply.

D100-51-00

I56-546-08R

12 3 4

中文翻译

下载PDF

与1151相关器件

型号	品牌	获取价格	描述	数据表
115-1001-FB	RCD	获取价格	Fixed Resistor, Wire Wound, 1W, 1000ohm, 45V, 1% +/-Tol,
115-1001-FT20Q	RCD	获取价格	Fixed Resistor, Wire Wound, 1W, 1000ohm, 45V, 1% +/-Tol, 20ppm/Cel,
115-1002-FT20	RCD	获取价格	Fixed Resistor, Wire Wound, 1W, 10000ohm, 45V, 1% +/-Tol, 20ppm/Cel,
115-100-JB	RCD	获取价格	Fixed Resistor, Wire Wound,
115101-02-0600	AMPHENOL	获取价格	BNC CRIMP PLUG TO BNC CRIMP PLUG, USING RG 174 CO-AXIAL CABLE, VARIOUS LENGTHS
115101-02-1200	AMPHENOL	获取价格	BNC CRIMP PLUG TO BNC CRIMP PLUG, USING RG 174 CO-AXIAL CABLE, VARIOUS LENGTHS
115101-02-1800	AMPHENOL	获取价格	BNC CRIMP PLUG TO BNC CRIMP PLUG, USING RG 174 CO-AXIAL CABLE, VARIOUS LENGTHS
115101-02-2400	AMPHENOL	获取价格	BNC CRIMP PLUG TO BNC CRIMP PLUG, USING RG 174 CO-AXIAL CABLE, VARIOUS LENGTHS
115101-02-36.00	AMPHENOL	获取价格	Cable Assembly, Communication Cable
115101-02-3600	AMPHENOL	获取价格	BNC CRIMP PLUG TO BNC CRIMP PLUG, USING RG 174 CO-AXIAL CABLE, VARIOUS LENGTHS

与1151相关文章

LTC1151C双通道±15V零漂移运算放大器全面解读
2024-06-21

229
解析光耦仿真器：升级光耦合器技术的必要性
2024-11-18

18
英伟达新一代Blackwell GPU过热问题致交付延迟
2024-11-18

12
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
2024-11-14

43

产品中心

服务支持

精选活动

关于我们

帮助中心

1151

1151 数据手册

与1151相关器件

与1151相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

1151

1151 数据手册

与1151相关器件

与1151相关文章

您还可以找

您在本页遇到什么问题？