10DPW_1.5 Series
10W - Single/Dual Output - Wide Input - Isolated & Regulated
DC-DC Converter
DC-DC Converter
10 Watt
The 10DPW_1.5 Series are isolated 10W DC/DC converters. Designed
with high efficiency, they allow the operating temperature range of these
units to be -40°C to +85°C with industry-standard footprint. Further
features include wide 2:1 input voltage range, remote on/off control,
short-circuit protection and over voltage protection.
Wide 2:1 input voltage range
Input/Output Isolation Voltage:
1.5KVDC
Operating Temperature Range:
-40°C to +100°C
Short circuit protection (SCP)
Remote On/Off
High efficiency
10W DIL package
Meet EN55022, Class A
(Radiation)
Shielded Metal Case with
Insulated Baseplate
RoHS Compliant
These converters are well suitable for battery operated equipment, mea-
surement equipment, telecom, wireless network and industry control
systems. Everywhere where isolated, tightly regulated voltages and com-
pact size are required.
Customer Design Available
Common specifications
Short circuit protection:
Cooling:
Output specifications
Hiccup, automatic recovery
Free air convection
-40°C~+100°C, with derating
-55°C~+125°C
Item
Test condition
Min
Typ
Max
2
Units
Minimum load
10ꢀ of full load
Operation temperature range:
Storage temperature range:
Maximum case temperature:
Switching frequency:
Storage humidity range:
Radiated emissions:
Conducted emissions:
Case material:
Output voltage
accuracy
Full load and nominal
Vin
ꢀ
ꢀ
Overload
protection
150
95°C
400kHz typ.
Cross regulation
Line regulation
Load regulation
Dual (25ꢀ-100ꢀ load%
5
ꢀ
ꢀ
ꢀ
95ꢀ max.
0.5
0.5
EN55022/Class A
EN55022/Class A
Five-Side Shielded Case
Epoxy (UL94V-0%
900,000 hours
17.5g
Single & Dual
(F.L-25ꢀF.L%
Ripple and noise
20MHz Bandwidth
• 3-15V output
• <15V output
100
1ꢀ of mVp-p
Vout
mVp-p
Potting material:
MTBF (MIL-HDBK-217F @25°C%:
Weight:
Transient response 50ꢀ load step change
settling time
350
µs
Input specifications
Isolation specifications
Item
Test condition
Pi Type
Min
Typ
Max
Units
VDC
Item
Test condition
Input to output
Test at 500VDC
Min
Typ
1500
Max
Units
VDC
MΩ
Input filter
Protection
Isolation voltage
Isolation resistance
Fuse recommended
1000
Input surge voltage
(100ms max.%
• Nominal input (12V%
• Nominal input (24V%
• Nominal input (48V%
25
50
100
Model selection:
WCTV_xxyyN##
Input reflected ripple
current
Nominal Vin and full
load
50
mAp-p
ms
W= Watt; C= Case; T= Type; V= Voltage Variation (omitted 10ꢀ%;
xx= Vin; yy= Vout; N= Numbers of Output; ##= Isolation (kVDC%
Start-up time
Nominal Vin and
constant resistive load
500
Example:
10DPW_2415S1.5
10= 10Watt; D= DIP; P= series; W= wide input (2:1) 18-36Vin;
15Vout; S= single output; 1.5= 1500VDC
Remote ON/OFF
• Converter: ON
• Converter: OFF
Open or 3.5V<Vr<12V
Short or 0V<Vr<1.2V
Sourcing current of
remote control pin
Nominal Vin
<0.2
mA
Note:
Idle input current (at
Remote OFF state%
Nominal Vin
<2.5
mA
1. Only typical model listed. Non-standard models will be different from the above,
please contact us for more details.
2. All specifications are typical at nominal input, full load and 25°C unless
otherwise stated.
3. In this datasheet, all the test methods of indications are based on corporate
standards.
Page 1 of 3
10DPW_1.5 – Rev. 2017-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com