10DPW4 Series
10W - Single/Dual Output - Wide Input - Isolated & Regulated
DC-DC Converter
DC-DC Converter
10 Watt
Wide 4:1 input voltage range
Input/Output Isolation Voltage:
1.5KVDC
High efficiency
The 10DPW4 Series are isolated 10W DC/DC converters. Designed with
high efficiency, they allow the operating temperature range of these
units to be -40°C to +85°C with industry-standard footprint. Further fea-
tures include wide 4:1 input voltage range, remote on/off control, short-
circuit protection and over voltage protection.
10W DIL package
Meet EN55022, Class A
(Radiation)
Operating Temperature Range:
-40°C to +100°C
Shielded Metal Case with
Insulated Baseplate
RoHS Compliant
Short circuit protection (SCP)
Remote On/Off
These converters are well suitable for battery operated equipment,
measurement equipment, telecom, wireless network and industry con-
trol systems. Everywhere where isolated, tightly regulated voltages and
compact size are required.
Customer Design Available
Common specifications
Short circuit protection:
Cooling:
Output specifications
Continuous, automatic recovery
Free air convection
-40°C~100°C
Item
Test condition
Min
Typ
Max
12
Units
W
Output power
Minimum load
Operation temperature range:
Storage temperature range:
Maximum case temperature:
Switching frequency:
Storage humidity range:
Radiated emissions:
Conducted emissions:
Case material:
10% of ful load
-55°C~+125°C
Output voltage
accuracy
Full load and nominal
Vin
2
%
%
100°C
Overload
protection
150
400kHz TYP
95% MAX
Line regulation
Load regulation
High Line to Low Line
0.5
0.5
%
%
EN55022/Class A
EN55022/Class A
Five-Side Shielded Case
Epoxy (UL94V-0)
900,000 hours
17.5g
Single & Dual
(F.L-25%F.L)
Ripple and noise
20MHz Bandwidth
100
mVp-p
µs
Transient respon-
se settling time
50% load step change
350
Potting material:
MTBF (MIL-HDBK-217F @25°C):
Weight:
Isolation specifications
Item
Test condition
Input to output
Test at 500VDC
Min
Typ
Max
Units
VDC
MΩ
Isolation voltage
Isolation resistance
1500
1000
Input specifications
Item
Test condition
Pi Type
Min
Typ
Max Units
VDC
Input filter
Protection
Example:
10DPW4_2415S1.5
10= 10Watt; D= DIP; P= series; W4= wide input (4:1) 9-36Vin; 15Vout;
S= single output; 1.5= 1500VDC
Fuse recommended
Input surge voltage
(100ms max.)
• Nominal input (12V)
• Nominal input (24V)
• Nominal input (48V)
25
50
100
Input reflected ripple
current
Nominal Vin and full
load
50
mAp-p
ms
Start-up time
Nominal Vin and
constant resistive
load
500
Note:
Remote ON/OFF
• Converter: ON
• Converter: OFF
Open or 3.5V<Vr<12V
Short or 0V<Vr<1.2V
1. Only typical model listed. Non-standard models will be different from the above,
please contact us for more details.
2. All specifications are typical at nominal input, full load and 25°C unless
otherwise stated.
3. In this datasheet, all the test methods of indications are based on corporate
standards.
Sourcing current of
remote control pin
Nominal Vin
<0.2
mA
Idle input current (at
Remote OFF state)
Nominal Vin
<2.5
mA
Page 1 of 3
10DPW4 – Rev. 2017-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com