Datasheet > 09-06-3110

09-06-3110

更新时间： 2024-01-12 11:14:08

品牌	Logo	应用领域
莫仕 - MOLEX		/
页数	文件大小	规格书
6页	171K
描述
IDT CHANGE HEAD Specification Sheet

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

09-06-3110 技术参数

生命周期：	Obsolete	Reach Compliance Code：	unknown
ECCN代码：	EAR99	HTS代码：	8536.69.40.40
风险等级：	5.75	其他特性：	TRIFURCON, POLARIZED
主体宽度：	0.37 inch	主体深度：	0.685 inch
主体长度：	1.734 inch	主体/外壳类型：	PLUG
连接器类型：	BOARD CONNECTOR	接触器设计：	PREASSEM CONN
联系完成配合：	TIN (200) OVER COPPER (100)	联系完成终止：	TIN (200) OVER COPPER (100)
触点性别：	MALE	触点材料：	BRASS
触点模式：	RECTANGULAR	触点电阻：	20 m Ω
触点样式：	BELLOWED TYPE	DIN 符合性：	NO
介电耐压：	2000VAC V	耐用性：	25 Cycles
滤波功能：	NO	IEC 符合性：	NO
最大插入力：	11.12 N	最小绝缘直径：	0.045 inch
绝缘电阻：	200000000 Ω	绝缘体颜色：	GREEN
绝缘体材料：	NYLON	JESD-609代码：	e3
MIL 符合性：	NO	插接触点节距：	0.156 inch
插接信息：	MULTIPLE MATING PARTS AVAILABLE	混合触点：	NO
安装选项1：	POLARIZED LCK	安装选项2：	PLASTIC
安装类型：	CABLE	装载的行数：	1
最高工作温度：	75 °C	最低工作温度：	-40 °C
选件：	GENERAL PURPOSE	极化密钥：	POLARIZED HOUSING
额定电流（信号）：	5 A	参考标准：	UL, CSA
可靠性：	COMMERCIAL	子类别：	Headers and Edge Type Connectors
端接类型：	IDC	触点总数：	11
UL 易燃性代码：	94V-2	最大线径：	24 AWG
最小线径：	27 AWG	撤离力-最小值：	5.3376 N
Base Number Matches：	1

09-06-3110 数据手册

Change head for IDT Connectors Series

RIB OF CONNECTOR FACING UP

2. Place the proper connector into the track; the rib of the connector should be facing up. See

Figure 3.

3. Compress the front pistol handle and slide the connector into the Change Head track until it

stops, release the pistol handle.

4. Operate the pistol to index the connector into the change head.

5. Place the proper wire into the slot above the connector. Make sure that the wire is fully seated.

6. Close the piston hand tool by moving the front operating handle while holding the wire in place.

7. Release the operating handle gently. During the return stroke the housing will automatically

advance to the next circuit position.

8. Check for wire insulation depth in the location slot. The wire insulation must be just below the

“eagle” of the connector housing. See Figure 4.

9. Repeat steps 4 thru 7 above for placement of additional wires until the last circuit of the

housing is completed.

10. To remove the completed wire/housing assembly from the piston hand tool, slide the assembly

Figure 3

TRACK

to the right and push out.

Note: After the last wire insertion has been made in the connector assembly, the assembly will not advance any further because the

feed pawl will have cleared the end of the connector body.

EAGLE

ADJUSTMENTS

Wire Insertion Depth

1. Remove the Change Head from the pistol handle.

2. To adjust the insertion depth of the wire use the Allen wrench which is included with Change

Head.

3. Place the Allen wrench into the feed adjustment set screw, which is located in the mounting

slot of the change head that goes into the piston handle. See Figure 1.

4. By rotating this setscrew, the insertion depth can be changed.

5. Clockwise (CW) will increase wire insertion depth. Counter Clockwise (CCW) will decrease wire

WIRE

CONNECTOR

HOUSING

insertion depth.

Figure 4

Guide Plate

The two fixing screws on the front guide plate offer a small amount of track adjustment. This should only be adjusted if the connector

does not run smoothly through the track.

Connector Locator

The small slotted spring ball screw in the body molding of the change head is used to adjust the connector locator.

1. The spring ball screw should be loosened for 2,3,4, and 5 circuits size connector housings using a 3mm wide screwdriver blade.

See Figure 1.

2. For larger circuit size connector housing the spring ball screw should be tightened. This will ensure correct and consistent feed

action during operation.

This is set at the factory and should not require adjustment.

Doc No. 011215196

Revision: A

Release Date: 05-15-06

Revision Date: 05-15-06

UNCONTROLLED COPY

Page 5 of 6

1 2 3 456

下载PDF

与09-06-3110相关器件

型号	品牌	描述	获取价格	数据表
09-06-3117	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-3118	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-3119	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-3120	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-3127	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格
09-06-3128	MOLEX	IDT CHANGE HEAD Specification Sheet	获取价格

与09-06-3110相关文章

STM32H743技术深度剖析与应用案例探索
2024-05-30

15
LM321中文资料解析：引脚功能介绍、技术特点、技术特性分析
2024-05-30

15
74HC14芯片资料介绍：性能特性分析、引脚介绍
2024-05-30

13
LM1875芯片手册：功放参数分析、引脚说明、电路设计要点
2024-05-30

10

产品中心

服务支持

精选活动

关于我们

帮助中心

09-06-3110

09-06-3110 技术参数

09-06-3110 数据手册

与09-06-3110相关器件

与09-06-3110相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

09-06-3110

09-06-3110 技术参数

09-06-3110 数据手册

与09-06-3110相关器件

与09-06-3110相关文章

您还可以找

您在本页遇到什么问题？