Recommended Circuit
COMMON SPECIFICATION
All the WRE_P-3W&WRF_P-3W Series have
been tested according to the following
recommended testing circuit before leaving
factory. This series should be tested under load.
Never be tested under no load (see Figure 1).
Item
Test Conditions
Min
Typ
15
Max
95
Units
%
Storage humidity
Operating temperature
Storage temperature
Temp. rise at full load
Lead temperature
Cooling
-40
-55
85
125
℃
Dual Output
1.5mm from case for 10 seconds
300
+Vout
0V
Vin
Free air convection
Cin
DC DC
Short circuit protection
Case material
MTBF
Continuous, automatic recovery
Plastic (UL94-V0)
GND
-Vout
Single Output
100
K hours
g
+Vout
0V
Vin
Cin
DC DC
(Figure 1)
Weight
17
GND
TYPICAL CHARECTERISTICS
If you want to further decrease the input/output
ripple, you can increase capacitance properly
or choose capacitors with low ESR. However,
the capacitance of the output filter capacitor
must be proper. If the capacitance is too big, a
startup problem might arise. For every channel
of output, provided the safe and reliable
operation is ensured, the greatest capacitance
of its filter capacitor sees (Table 1).
Temperature Derating Graph
Safe Operating Area
General: Cin: 12V
100μF
Operating Temp.( C )
24V 10μF-47μF
Cout: 10μF/100mA
OUTLINE DIMENSIONS & PIN CONNECTIONS
. Output Extemal Capacitor Table(Table 1)
Single Vout
(VDC)
Cout
(uF)
Dual Vout
(VDC)
Cout
(uF)
First Angle Projection
31.80(1.252)
5
9
1000
680
470
330
±5
±9
680
470
330
220
RECOMMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch),
diameter:1.00mm(0.039inch)
12
15
±12
±15
2 3
91011
(Bottom View)
Single /Dual Output
Input Current
2322
16 14
15
When it is used in unregulated power supply,
be sure that the fluctuating range of the power
supply and the rippled voltage do not exceed
the module standard. Input current of power
supply should afford the startup current of this
kind of DC/DC module. (Figure 2)
16
9
15 14
10 11
23
2
22
3
2.54
(0.100)
4.25
(0.167)
(Side View)
General: Ip ≤1.4*Iin-max
FOOTPRINT DETAILS
Dual
GND
0V
Pin
2,3
9
Single
GND
Ip
11
10,15
14
16
22,23
NC
NC
+Vo
0V
-Vo
NC
+Vo
0V
Note:
Unit:mm(inch)
Pin diameter:0.50mm(0.020inch)
Pin diameter tolerances: 0.05mm(
General tolerances: 0.25mm( 0.010inch)
Input Voltage
Range
±
±0.002inch)
Vin
Vin
±
±
NC:No Connection
Input Voltage (V)
APPLICATION NOTE
Requirement On Output Load
In order to ensure the product operate efficiently and reliably, in addition to a max load
(namely full load), a minimum load is specified for this kind of DC/DC converter. Make sure
the specified range of input voltage is not exceeded, the minimum output load no less than
10% load. If the actual load is less than the specified minimum load, the output ripple may
increase sharply while its efficiency and reliability will reduce greatly. If the actual output
power is very small, please add an appropriate resistor as extra loading, or contact our
company for other lower output power products.
No parallel connection or plug and play.
MORNSUN reserves the copyright
Specifications subject to change without notice.
WRE_P-3W & WRF_P-3W
A/0-2008
Page 2 of 2