5秒后页面跳转
UCC2912PWPTR PDF预览

UCC2912PWPTR

更新时间: 2024-10-02 12:59:43
品牌 Logo 应用领域
德州仪器 - TI /
页数 文件大小 规格书
16页 659K
描述
暂无描述

UCC2912PWPTR 数据手册

 浏览型号UCC2912PWPTR的Datasheet PDF文件第2页浏览型号UCC2912PWPTR的Datasheet PDF文件第3页浏览型号UCC2912PWPTR的Datasheet PDF文件第4页浏览型号UCC2912PWPTR的Datasheet PDF文件第5页浏览型号UCC2912PWPTR的Datasheet PDF文件第6页浏览型号UCC2912PWPTR的Datasheet PDF文件第7页 
ꢀ ꢁꢁ ꢂꢃ ꢄꢂ  
ꢀ ꢁꢁ ꢅꢃ ꢄꢂ  
ꢆꢇꢈ ꢉ ꢇꢊꢋ ꢋ ꢊꢌꢍ ꢎ ꢏꢈ ꢐ ꢑꢒꢊꢆ ꢆꢈ ꢒ ꢎꢇ ꢋ ꢊꢓ ꢊ ꢉꢎ ꢇ  
SLUS241D − MARCH 1994 - REVISED NOVEMBER 2003  
D
D
D
D
D
D
D
D
Integrated 0.15-Power MOSFET  
3-V to 8-V Operation  
D
Unidirectional Switch  
Thermal Shutdown  
Fault-Output Indicator  
D
D
D
Digital Programmable Current Limit  
from 0 A to 3 A  
Maximum-Output Current Can Be Set to 1 A  
Above the Programmed Fault Level or to a  
Full 4 A  
Electronic Circuit Breaker Function  
1µA I  
When Disabled  
CC  
D
Power SOIC, Low-Thermal Resistance  
Packaging  
Programmable On-Time  
Programmable Start Delay  
Fixed 3% Duty Cycle  
description  
The UCC3912 family of hot swap power managers provides complete power management, hot swap capability,  
and circuit breaker functions. The only component required to operate the device, other than supply bypassing,  
is the fault timing capacitor, C . All control and housekeeping functions are integrated, and externally  
T
programmable. These include the fault current level, maximum output-sourcing current, maximum fault time,  
and startup delay. In the event of a constant fault, the internal fixed 3% duty cycle ratio limits average output  
power.  
The internal 4-bit DAC allows programming of the fault level current from 0 A to 3 A with 0.25-A resolution. The  
IMAX control pin sets the maximum sourcing current to 1 A above the fault level when driven low, and to a full  
4 A when driven high for applications which require fast output capacitor charging.  
When the output current is below the fault level, the output MOSFET is switched on with a nominal on resistance  
of 0.15 . When the output current exceeds the fault level, but is less than the maximum sourcing level, the  
output remains switched on, but the fault timer starts charging C . Once C charges to a preset threshold, the  
T
T
switch is turned off, and remains off for 30 times the programmed fault time. When the output current reaches  
the maximum sourcing level, the MOSFET transitions from a switch to a constant current source. (continued)  
block diagram  
H = 4 A  
2
3
VIN  
VIN  
IMAX 10  
30 mV  
V
REVERSE VOLTAGE  
COMPARATOR  
CHARGE  
PUMP  
+
OUT  
CURRENT SENSE  
4 A  
POWER  
FET  
+
MAX CURRENT  
LEVEL  
LINEAR CURRENT AMPLIFIER  
H = OPEN  
1 A  
ABOVE  
FAULT  
ON TIME  
CONTROL  
14 VOUT  
15 VOUT  
CURRENT FAULT  
LEVEL 0A TO 3 A  
+
3% DUTY  
CYCLE  
THERMAL  
SHUTDOWN  
OVERCURRENT  
COMPARATOR  
1.5 V  
0 A−3 A  
0.25  
RES  
+
INTERNAL  
BIAS  
1
SHTDWN  
6
7
8
9
5
4
13 12  
11  
16  
UDG-99146  
B3 B2 B1 B0  
4 BIT DAC  
GND  
CT  
FAULT  
HEATSINK  
GND PINS  
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of  
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.  
ꢐꢢ  
Copyright 2003, Texas Instruments Incorporated  
ꢞ ꢢ ꢟ ꢞꢗ ꢘꢬ ꢚꢙ ꢝ ꢥꢥ ꢣꢝ ꢛ ꢝ ꢜ ꢢ ꢞ ꢢ ꢛ ꢟ ꢧ  
1
www.ti.com  

与UCC2912PWPTR相关器件

型号 品牌 获取价格 描述 数据表
UCC2913 TI

获取价格

Negative Voltage Hot Swap Power Manager
UCC2913D TI

获取价格

NEGATIVE VOLTAGE HOT SWAP POWER MANAGER
UCC2913DG4 TI

获取价格

具有工业温度范围的浮动负电压热插拔控制器,带电流限制功能 | D | 8 | -40 to
UCC2913DR TI

获取价格

1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO8, PLASTIC, MS-012AA, SOIC-8
UCC2913DTR TI

获取价格

NEGATIVE VOLTAGE HOT SWAP POWER MANAGER
UCC2913DTRG4 TI

获取价格

NEGATIVE VOLTAGE HOT SWAP POWER MANAGER
UCC2913J TI

获取价格

NEGATIVE VOLTAGE HOT SWAP POWER MANAGER
UCC2913N TI

获取价格

NEGATIVE VOLTAGE HOT SWAP POWER MANAGER
UCC2913NG4 TI

获取价格

1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8, GREEN, PLASTIC, DIP-8
UCC2913NR TI

获取价格

IC 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP8, PLASTIC, PDIP-8, Power Management Circuit