5秒后页面跳转
UAA1570HL PDF预览

UAA1570HL

更新时间: 2024-01-14 03:12:28
品牌 Logo 应用领域
恩智浦 - NXP 全球定位系统
页数 文件大小 规格书
76页 893K
描述
Global Positioning System GPS front-end receiver circuit

UAA1570HL 技术参数

生命周期:Obsolete零件包装代码:QFP
包装说明:LFQFP,针数:48
Reach Compliance Code:unknownHTS代码:8542.39.00.01
风险等级:5.84JESD-30 代码:S-PQFP-G48
长度:7 mm功能数量:1
端子数量:48最高工作温度:85 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:LFQFP封装形状:SQUARE
封装形式:FLATPACK, LOW PROFILE, FINE PITCH认证状态:Not Qualified
座面最大高度:1.6 mm标称供电电压:3 V
表面贴装:YES电信集成电路类型:TELECOM CIRCUIT
温度等级:INDUSTRIAL端子形式:GULL WING
端子节距:0.5 mm端子位置:QUAD
宽度:7 mmBase Number Matches:1

UAA1570HL 数据手册

 浏览型号UAA1570HL的Datasheet PDF文件第3页浏览型号UAA1570HL的Datasheet PDF文件第4页浏览型号UAA1570HL的Datasheet PDF文件第5页浏览型号UAA1570HL的Datasheet PDF文件第7页浏览型号UAA1570HL的Datasheet PDF文件第8页浏览型号UAA1570HL的Datasheet PDF文件第9页 
Philips Semiconductors  
Product specification  
Global Positioning System (GPS) front-end  
receiver circuit  
UAA1570HL  
6
PINNING INFORMATION  
PIN VOLTAGE  
TYPICAL VALUES (V)  
SYMBOL  
PIN  
DESCRIPTION  
VCC = 2.7 V VCC = 5 V  
VCCA(LNA2)  
1
2.7  
5
LNA2 power supply: DC operation range 2.7 to 5 V; use close  
proximity RF decoupling to pins 2, 4 and 5  
LNA2GND1  
LNA2IN  
2
3
4
5
6
0
0
LNA2 ground 1: minimize RF ground inductance  
LNA2 input: use external RF AC coupling  
0.815  
0
0.807  
0
BIASGND2  
LNA2GND2  
LNA2OUT  
LNA2 bias circuit ground: minimize RF ground inductance  
LNA2 ground 2: minimize RF ground inductance  
0
0
1.48  
3.629  
LNA2 output: use external RF AC coupling. The DC voltage is  
approximately 1.3 V below the VCCA(LNA2) supply on pin 1.  
CLOCK  
7
CMOS level CMOS level Serial interface clock input: this DC coupled CMOS CLOCK  
input moves 20-bit programming words into the synthesizer  
DATA input register while the STROBE is LOW. A DC  
short-circuit to ground is recommended with the default  
frequency plan.  
REFIN  
8
9
1.69  
3.99  
Reference input: use external AC coupling. The DC voltage is  
approximately 1 V below the VCCA(PLL) supply on pin 36.  
VCCA(VCO)  
TANK  
2.7  
5
VCO power supply: DC operation range 2.7 to 5 V; use critical  
close proximity RF decoupling to pin 11  
10 1.92  
1.92  
VCO negative impedance resonator port: use the absolute  
minimum trace lengths and widths and keep the loop to the VCO  
ground pin 11 as short as possible, while centring the COMP  
output voltage at pin 40 within the charge pump output voltage  
range given in Chapter 11 by adjusting the resonator inductance  
and/or required AC coupling component.  
VCOGND  
P12GND  
11  
12  
13  
0
0
0
0
0
VCO ground: minimize RF ground inductance; use critical  
close proximity RF decoupling to VCO supply pin 9  
this pin provides additional RF shielding and has to be  
connected to ground  
MXPGND  
MX1IN  
0
RF mixer preamplifier ground: minimize RF ground inductance  
14 0.82  
0.81  
RF mixer preamplifier input: use external AC coupling and RF  
matching  
MX1GND  
VCCA(MX1P)  
IF1P  
15  
0
0
5
5
RF mixer ground: minimize RF ground inductance; use critical  
close proximity RF decoupling to VCCA(MX1P) supply pin 16  
16 2.7  
17 2.7  
RF preamplifier/mixer power supply: DC operation range  
2.7 to 5 V; use critical close proximity RF decoupling to pin 15  
RF mixer IF positive output: DC couple this output pin to the  
VCCA(MX1P) supply through first IF filter inductors or RF chokes.  
Capacitively decouple the supply near the output inductors.  
Balanced first mixer IF1 outputs are recommended. Prevent  
externally squared reference harmonics from entering the first IF  
signal path or components.  
1999 May 10  
6

与UAA1570HL相关器件

型号 品牌 描述 获取价格 数据表
UAA170 INFINEON LED Driver for Light Spot Displays

获取价格

UAA180 INFINEON LED Driver for Light Band Displays

获取价格

UAA2016 ONSEMI ZERO VOLTAGE SWITCH POWER CONTROLLER

获取价格

UAA2016/D ONSEMI Zero Voltage Switch Power Controller

获取价格

UAA2016_06 ONSEMI Zero Voltage Switch Power Controller

获取价格

UAA2016AD ONSEMI Zero Voltage Switch Power Controller

获取价格