TDA9897; TDA9898
NXP Semiconductors
Multistandard hybrid IF processing
Table 1.
Quick reference data …continued
VP = 5 V; Tamb = 25 °C.
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
ϕn(synth)
synthesizer phase noise
with 4 MHz crystal oscillator
reference; fsynth = 31 MHz;
fIF = 36 MHz
[8]
[8]
[8]
[8]
at 1 kHz
89
89
98
115
-
99
99
102
119
-
-
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
dB
at 10 kHz
at 100 kHz
at 1.4 MHz
-
-
-
αripple(pb)LIF low IF pass-band ripple
6 MHz bandwidth
2.7
2.7
2.7
-
7 MHz bandwidth
-
-
dB
8 MHz bandwidth
-
-
dB
αstpb
αimage
C/N
stop-band attenuation
image rejection
8 MHz band; f = 15.75 MHz
−10 MHz to 0 MHz; BP on
at fo = 4.9 MHz;
30
30
112
40
34
118
dB
-
dB
[8][9][10]
carrier-to-noise ratio
-
dBc/Hz
Vi(IF) = 10 mV (RMS);
see Figure 37
Digital zero IF
Vo(dif)(p-p)
[7]
peak-to-peak differential output
voltage
between pin OUT1A and
pin OUT1B or between
pin OUT2A and pin OUT2B;
W4[7] = 0
-
-
2
-
-
V
[8]
[8]
GIF(max)
maximum IF gain
output peak-to-peak level to
input RMS level ratio
89
dB
GIF(cr)
fsynth
control range IF gain
synthesizer frequency
synthesizer phase noise
60
-
66
-
-
-
dB
see Table 35 and Table 36
MHz
ϕn(synth)
with 4 MHz crystal oscillator
reference; fsynth = 31 MHz;
fIF = 36 MHz
[8]
[8]
[8]
[8]
at 1 kHz
89
99
-
-
-
-
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
at 10 kHz
at 100 kHz
at 1.4 MHz
89
99
98
102
119
115
Reference frequency input from external source
[11]
fref
reference frequency
W7[7] = 0
-
4
-
MHz
mV
Vref(RMS)
RMS reference voltage
W7[7] = 0; see Figure 34
and Figure 46
15
150
500
[1] Values of video and sound parameters can be decreased at VP = 4.5 V.
[2] AC load; CL < 20 pF and RL > 1 kΩ. The sound carrier frequencies (depending on TV standard) are attenuated by the integrated sound
carrier traps.
[3] The sound carrier trap can be bypassed by setting the I2C-bus bit W2[0] to logic 0; see Table 24. In this way the full composite video
spectrum appears at pin CVBS. The video amplitude is reduced to 1.1 V (p-p).
[4] Condition: luminance range (5 steps) from 0 % to 100 %. Measurement value is based on 4 of 5 steps.
[5] Measurement using 200 kHz high-pass filter, 5 MHz low-pass filter and subcarrier notch filter (“ITU-T J.64”).
[6] To match the AFC output signal to different tuning systems a current output is provided. The test circuit is given in Figure 19. The
AFC steepness can be changed by resistors R1 and R2.
TDA9897_TDA9898_3
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 03 — 11 January 2008
6 of 103