Philips Semiconductors
Product specification
Satellite sound circuit with noise reduction
TDA8742; TDA8742H
channel input, pin 18 (14) via a 10.7 MHz ceramic
bandpass filter.
FUNCTIONAL DESCRIPTION
Satellite sound
The filtered signal is AC-coupled to a limiter/amplifier and
then to a PLL demodulator. The PLL FM demodulator
ensures that the demodulator is alignment-free. High gain
and DC error signals from the PLL, which are
superimposed on the demodulator output, require DC
decoupling. A buffer amplifier is used to amplify the signal
to the same level as the secondary channels and
decouples DC using an electrolytic capacitor connected to
pin 41 (37). The demodulator output signal is fed to pin 20
(16) via an internal resistor. The output signal can be
de-emphasized by means of this resistor and an external
capacitor connected to ground.
The baseband signal coming from a satellite tuner
contains the demodulated video signal plus a number of
sound carriers to facilitate reception of a
PAL/NTSC/SECAM satellite signal.
Nearest to the video signal is the main sound carrier which
carries the single channel sound related to the video. This
is an FM modulated carrier with a fixed pre-emphasis. The
carrier frequency can be in the range of 5.8 to 6.8 MHz.
Additionally, a number of optional secondary sound
carriers may be present which can be used for stereo or
multi-language sound related to the video, or for unrelated
radio sound. These carriers are also FM modulated, but for
better sound quality (improved signal-to-noise
Capacitor value = de-emphasis time constant per1500
(for 50 µs: 33 nF).
performance) broadcast satellites (e.g. ‘ASTRA’) use a
noise reduction system (adaptive pre-emphasis circuit,
combined with a fixed pre-emphasis).
From here the signal is fed to the output selectors. The
signal is amplified to 500 mV (RMS) (i.e. −6 dBV) in the
output amplifiers.
These secondary carrier frequencies can be in the range
of 6.30 to 8.28 MHz.
Secondary channels
Up to eight secondary channels are available at pins 2, 4,
6, 8, 10, 12, 14 and 16 (1, 3, 5, 7, 9, 11, 40 and 42).
External ceramic bandpass filters, tuned to the required
secondary sound carrier frequencies, route these signals
to the inputs. This enables the demodulation of eight
different channel; frequencies, which are derived from the
baseband, by using an external mixer and oscillator
frequency synthesizer.
The TDA8742; H contains all circuitry for processing the
main channel and for two secondary channels, from
baseband signal to line (SCART) output drivers. The
desired frequencies can be routed to the device via
bandpass filters.
Main channel (see Fig.1)
The lock-in range of the main channel PLL can be
switched between 5.5 to 7.5 MHz, PLL off and 10.0 to
11.5 MHz using the MCS signal at pin 7 (2) [when pin 7 (2)
is at logic 0, being a voltage from 0 to 1.2 V, the lock-in
range = 5.5 to 7.5 MHz; when pin 7 (2) is at logic 1, being
a voltage from 3.5 V until VP, the lock-in range = 10.0 to
11.5 MHz; when pin 7 (2) is in the mid voltage position,
being a voltage from 1.8 to 2.8 V, the main channel PLL is
switched off]. The voltage is then determined by the
resistor divider at this pin between VP and ground.
For stereo applications the TDA8742; TDA8742H contains
two identical secondary sound processing channels. For
each channel it is possible to select from four inputs (IN-A,
IN-B, IN-C and IN-D) using the input selector
(see Table 1). With the input switch several stereo signals
or languages can be selected for demodulation. It should
be noted that the inputs are identical and can be freely
interchanged Secondary Channel 1 will also be referred to
as ‘LEFT’ or ‘LANGUAGE 1’ and secondary Channel 2 will
also be referred to as ‘RIGHT’ or ‘LANGUAGE 2’.
If only one fixed carrier frequency for the main channel is
to be demodulated (e.g. 6.5 MHz), the lock-in range of the
PLL should be switched to 5.5 to 7.5 MHz. The baseband
signal is applied to the main channel input, pin 18 (14) via
a 6.5 MHz ceramic bandpass filter. Alternatively, if there is
a requirement to demodulate different main channel
frequencies, these frequencies can be transferred to a
fixed intermediate frequency (e.g. 10.7 MHz) using an
external mixer and oscillator-frequency synthesizer. In this
event the lock-in range of the PLL should be switched to
10.0 to 11.5 MHz. The IF signal is applied to the main
From the input selector switch the signals are coupled to
limiter/amplifiers and then to the PLL demodulators.
Processing is similar to the main channel. The
demodulator output signal is amplified in a buffer amplifier
and DC decoupled using electrolytic capacitors connected
to pins 40 (36) (left) and 42 (38) (right). The output level is
set with a 220 Ω resistor connected in series with the
capacitor.
October 1994
7
5秒后页面跳转
PCF8574资料解读：主要参数分析、引脚说明
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
一文带你了解压敏电阻器在直流电路中的过压保护作用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
