Datasheet > TDA18211HD

TDA18211HD

更新时间： 2022-12-24 19:07:06

品牌	Logo	应用领域
恩智浦 - NXP		/
页数	文件大小	规格书
66页	309K
描述
DVB-T Silicon Tuner IC

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

TDA18211HD 数据手册

TDA18211HD

NXP Semiconductors

DVB-T Silicon Tuner IC

8. Functional description

The RF input signal is driven to a low-noise ampliﬁer. It is then band-pass ﬁltered,

ampliﬁed and fed to the image rejection mixer. The mixer downconverts the RF signal to a

low IF, which depends on channel bandwidth (standard IF ﬁlters are implemented for

6/7/8 MHz channel bandwidths; see Table 41).

The gain between the antenna pin (pin RF_IN) and the loop-through pin (pin LT) is 0 dB.

The TDA18211HD requires a single 16 MHz crystal for clock generation.

When bit XTOUT_ON = 1, a differential sine wave clock reference is available on pins

XTOUTP and XTOUTN to drive a channel decoder.

8.1 Master and slave operation

The TDA18211HD allows easy dual-tuner conﬁguration.

Each individual tuner has to be set either in Master mode or Slave mode by applying a DC

voltage on the XTOUT_MS pin; see Table 4. This will decide whether the crystal oscillator

part is used as negative impedance connected to the crystal part or as a current buffer.

Table 4.

Master and slave selection

Voltage on pin XTOUT_MS

0 V to 0.1V_CC

Tuner type

master

Crystal oscillator

negative impedance presented to the crystal

current input buffer

0.4V_CCto 0.6V_CC

slave

In dual-tuner application:

• The ﬁrst tuner is set in Master mode

• The second tuner has to be set in Slave mode

In single-tuner application:

• The tuner must be set in Master mode.

8.2 Tuner outputs

The tuner provides a slave tuner output (pin STO) and a loop-through output (pin LT).

Those outputs are used to transmit the antenna signal to other tuners. Each output has its

own characteristics (see Table 56 and Table 57)

8.2.1 Loop-through output

The gain between the antenna connector and the loop-through pin (pin LT) equals 0 dB.

This pin can be connected to any consumer electronic equipment.

8.2.2 Slave tuner output

The slave tuner output (pin STO) must be connected to the RF input of the slave tuner

TDA18211HD in case of dual-tuner applications.

The gain between the antenna connector and the slave tuner output can change

according to the input level. The slave tuner will automatically compensate the gain

change, using the MASTERSYNC and FREEZE signals.

TDA18211HD_5

Product data sheet

Rev. 05 — 2 June 2009

6 of 66

1...3 4 567 8 9...66

下载PDF

与TDA18211HD相关器件

型号	品牌	描述	获取价格	数据表
TDA18211HD/C2,518	NXP	IC VIDEO TUNER, PQCC64, 9 X 9 MM, 1.60 MM HEIGHT, ROHS COMPLIANT, PLASTIC, SOT903-1, HLQFN	获取价格
TDA18211HD/C2,551	NXP	IC VIDEO TUNER, PQCC64, 9 X 9 MM, 1.60 MM HEIGHT, ROHS COMPLIANT, PLASTIC, SOT903-1, HLQFN	获取价格
TDA18211HDC2	NXP	DVB-T Silicon Tuner IC	获取价格
TDA18212HN	NXP	Silicon Tuner for terrestrial and cable digital TV reception	获取价格
TDA18212HN/S/C1	NXP	SPECIALTY CONSUMER CIRCUIT, PQCC40, 6 X 6 MM, 0.85 MM HEIGHT, ROHS COMPLIANT, PLASTIC, SOT	获取价格
TDA18212HN/S/C1,51	NXP	TDA18212HN - Silicon Tuner for terrestrial and cable digital TV reception QFN 40-Pin	获取价格