Datasheet > R0990LS06C

R0990LS06C

更新时间： 2023-05-15 00:00:00

品牌	Logo	应用领域
IXYS		/
页数	文件大小	规格书
12页	254K
描述
Silicon Controlled Rectifier, 2001A I(T)RMS, 600V V(DRM), 600V V(RRM), 1 Element, 101A336, 3 PIN

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

R0990LS06C 数据手册

WESTCODE ^{Positive development in power electronics}

R0990LS06 to R0990LS08

The total dissipation is now given by:

E f

W_(TOT)W_(original)

12.2 Determination without Measurement

In circumstances where it is not possible to measure voltage and current conditions, or for design

purposes, the additional losses E in joules may be estimated as follows.

Let E be the value of energy per reverse cycle in joules (curves in Figure 9).

Let f be the operating frequency in Hz

T_SINK

−

E R_thf

(

)

(

new

)

(

original

)

Where T_{SINK (new)}is the required maximum heat sink temperature and

T_{SINK (original)}is the heat sink temperature given with the frequency ratings.

A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage

to a peak value (V_rm) of 67% of the maximum grade. If a different grade is being used or V_rmis other than

67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value

obtained from the curves.

NOTE 1

- Reverse Recovery Loss by Measurement

This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring

the charge care must be taken to ensure that:

(a) a.c. coupled devices such as current transformers are not affected by prior passage of high

amplitude forward current.

(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope

to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal

damped snubber, connected across diode anode to cathode. The formula used for the calculation

of this snubber is shown below:

V_r

R²= 4

C_S

Where: V_r= Commutating source voltage

C_S= Snubber capacitance

= Snubber resistance

13.0 Gate Drive

Ω

The recommended pulse gate drive is 30V, 15 with a short-circuit current rise time of not more than

0.5µs. This gate drive must be applied when using the full di/dt capability of the device.

The duration of pulse may need to be configured with respect to the application but should be no shorter

than 20µs, otherwise an increase in pulse current could be needed to supply the resulting increase in

charge to trigger.

Data Sheet. Types R0990LS06x to R0990LS08x Issue 1

Page 5 of 12

April, 2001

1 2 3 456 7 8...12

下载PDF

与R0990LS06C相关器件

型号	品牌	描述	获取价格	数据表
R0990LS08A	IXYS	Silicon Controlled Rectifier, 2001A I(T)RMS, 800V V(DRM), 800V V(RRM), 1 Element, 101A336,	获取价格
R0990LS08B	IXYS	Silicon Controlled Rectifier, 2001A I(T)RMS, 800V V(DRM), 800V V(RRM), 1 Element, 101A336,	获取价格
R09A11H11	PRODUCTWELL	ROTARY POTENTIOMETER	获取价格
R09A11H21	PRODUCTWELL	ROTARY POTENTIOMETER	获取价格
R09A11HB1	PRODUCTWELL	ROTARY POTENTIOMETER	获取价格
R09A11V1	PRODUCTWELL	ROTARY POTENTIOMETER	获取价格