1.3 ELECTRODE DESIGN
Figure 1-3 Internal Switching & Timing
ELECTRODE
1.3.1 ELECTRODE
G
EOMETRY AND
S
IZE
Result
There is no restriction on the shape of
the electrode; in most cases common
sense and a little experimentation can
result in a good electrode design. The
QT118H will operate equally well with
long, thin electrodes as with round or
square ones; even random shapes are
acceptable. The electrode can also be
a 3-dimensional surface or object.
Sensitivity is related to electrode
surface area, orientation with respect
to the object being sensed, object
composition, and the ground coupling
quality of both the sensor circuit and
the sensed object.
SNS2
Cs
Start
Cx
Done
SNS1
C harge
Amp
1.3.2 KIRCHOFF
’S
CURRENT
LAW
Like all capacitance sensors, the
QT118H relies on Kirchoff’s Current
Law (Figure 1-5) to detect the change
crumpled into a ball. Virtual ground planes are more effective
and can be made smaller if they are physically bonded to
other surfaces, for example a wall or floor.
in capacitance of the electrode. This law as applied to
capacitive sensing requires that the sensor’s field current
must complete a loop, returning back to its source in order for
capacitance to be sensed. Although most designers relate to
Kirchoff’s law with regard to hardwired circuits, it applies
equally to capacitive field flows. By implication it requires that
the signal ground and the target object must both be coupled
together in some manner for a capacitive sensor to operate
properly. Note that there is no need to provide actual
hardwired ground connections; capacitive coupling to ground
(Cx1) is always sufficient, even if the coupling might seem
very tenuous. For example, powering the sensor via an
isolated transformer will provide ample ground coupling,
since there is capacitance between the windings and/or the
transformer core, and from the power wiring itself directly to
'local earth'. Even when battery powered, just the physical
size of the PCB and the object into which the electronics is
embedded will generally be enough to couple a few
‘Ground’ as applied to capacitive fields can also mean power
wiring or signal lines. The capacitive sensor, being an AC
device, needs only an AC ground return.
1.3.5 SENSITIVITY
ADJUSTMENT
1.3.5.1 Gain Pin
The QT118H can be set for one of 3 gain levels using option
pin 5 (Table 1-1). This sensitivity change is made by altering
the internal numerical threshold level required for a detection.
Note that sensitivity is also a function of other things: like the
values of Cs and Cx, electrode size, shape, and orientation,
the composition and aspect of the object to be sensed, the
thickness and composition of any overlaying panel material,
and the degree of ground coupling of both sensor and object.
The Gain input should never be connected to a pullup or
pulldown resistor or tied to anything other than SNS1 or
SNS2, or left unconnected (for high gain setting).
picofarads back to local earth.
1.3.3 VIRTUAL
C
APACITIVE
GROUNDS
When detecting human contact (e.g. a fingertip), grounding
of the person is never required. The human body naturally
has several hundred picofarads of ‘free space’ capacitance to
the local environment (Cx3 in Figure 1-4), which is more than
two orders of magnitude greater than that required to create
a return path to the QT118H via earth. The QT118H's PCB
however can be physically quite small, so there may be little
‘free space’ coupling (Cx1 in Figure 1-4) between it and the
environment to complete the return path. If the QT118H
circuit ground cannot be earth grounded by wire, for example
via the supply connections, then a ‘virtual capacitive ground’
may be required to increase return coupling.
Figure 1-4 Kirchoff's Current Law
C
X2
Sense E lectrode
A ‘virtual capacitive ground’ can be created by connecting the
QT118H’s own circuit ground to:
SENSOR
- A nearby piece of metal or metallized housing;
- A floating conductive ground plane;
- Another electronic device (to which its might be
connected already).
C
X1
Free-floating ground planes such as metal foils should
maximize exposed surface area in a flat plane if possible. A
square of metal foil will have little effect if it is rolled up or
C
X3
Surrounding environm ent
lq
3
QT118H R1.08 / 0405
5秒后页面跳转
PCF8574资料解读：主要参数分析、引脚说明
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
一文带你了解压敏电阻器在直流电路中的过压保护作用
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
