5秒后页面跳转
Q24T15050-NBA0G PDF预览

Q24T15050-NBA0G

更新时间: 2024-01-24 13:36:25
品牌 Logo 应用领域
BEL /
页数 文件大小 规格书
14页 325K
描述
DC-DC Regulated Power Supply Module, 1 Output, 75W, Hybrid,

Q24T15050-NBA0G 技术参数

是否Rohs认证: 符合生命周期:Obsolete
包装说明:,Reach Compliance Code:compliant
ECCN代码:EAR99Factory Lead Time:20 weeks
风险等级:5.23其他特性:REMOTE SHUTDOWN
模拟集成电路 - 其他类型:DC-DC REGULATED POWER SUPPLY MODULE认证:UL, DEMKO
效率(主输出):88.5%高度:8.5 mm
最大输入电压:36 V最小输入电压:18 V
标称输入电压:24 VJESD-30 代码:R-XDMA-P8
长度:58.42 mm最大电网调整率:0.04%
最大负载调整率:0.04%功能数量:1
输出次数:1端子数量:8
最高工作温度:85 °C最低工作温度:-40 °C
最大输出电流:15 A最大输出电压:5.5 V
最小输出电压:4 V标称输出电压:5 V
封装主体材料:UNSPECIFIED封装形状:RECTANGULAR
封装形式:MICROELECTRONIC ASSEMBLY峰值回流温度(摄氏度):NOT APPLICABLE
认证状态:Not Qualified纹波电压(主输出):0.0106 Vrms
子类别:Power Supply Modules表面贴装:NO
技术:HYBRID端子形式:PIN/PEG
端子位置:DUAL处于峰值回流温度下的最长时间:NOT APPLICABLE
最大总功率输出:75 W微调/可调输出:YES
热身时间:0.0025 s宽度:36.83 mm
Base Number Matches:1

Q24T15050-NBA0G 数据手册

 浏览型号Q24T15050-NBA0G的Datasheet PDF文件第5页浏览型号Q24T15050-NBA0G的Datasheet PDF文件第6页浏览型号Q24T15050-NBA0G的Datasheet PDF文件第7页浏览型号Q24T15050-NBA0G的Datasheet PDF文件第9页浏览型号Q24T15050-NBA0G的Datasheet PDF文件第10页浏览型号Q24T15050-NBA0G的Datasheet PDF文件第11页 
Q24T15050 DC-DC Converter Data Sheet  
18-36 VDC Input; 5 VDC @ 15A Output  
tween 25°C and 85°C, with airflow rates from 30 to 500 LFM  
(0.15 to 2.5 m/s), and vertical and horizontal converter  
mounting.  
Characterization  
General Information  
For each set of conditions, the maximum load current was  
defined as the lowest of:  
The converter has been characterized for many operational  
aspects, to include thermal derating (maximum load current  
as a function of ambient temperature and airflow) for vertical  
and horizontal mounting, efficiency, start-up and shutdown  
parameters, output ripple and noise, transient response to  
load step-change, overload and short circuit.  
(i) The output current at which either any FET junction tem-  
perature did not exceed a maximum specified temperature  
(either 105°C or 120°C) as indicated by the thermographic  
image, or  
(ii) The nominal rating of the converter (15 A)  
The following pages contain specific plots or waveforms as-  
sociated with the converter. Additional comments for specific  
data are provided below.  
During normal operation, derating curves with maximum FET  
temperature less than or equal to 120°C should not be ex-  
ceeded. Temperature on the PCB at the thermocouple loca-  
tion shown in Fig. 28 should not exceed 118°C in order to  
operate inside the derating curves.  
Test Conditions  
All data presented were taken with the converter soldered to  
a test board, specifically a 0.060” thick printed wiring board  
(PWB) with four layers. The top and bottom layers were not  
metalized. The two inner layers, comprising two-ounce cop-  
per, were used to provide traces for connectivity to the con-  
verter.  
Efficiency  
Efficiency vs. load current plots are shown in Figs. 14 and 16  
for ambient temperature of 25ºC, airflow rate of 300 LFM  
(1.5 m/s), both vertical and horizontal orientations, and input  
voltages of 18 V, 27 V and 36 V. Also, plots of efficiency vs.  
load current, as a function of ambient temperature with Vin =  
27 V, airflow rate of 200 LFM (1 m/s) are shown for both a  
vertically and horizontally mounted converter in Figs. 15 and  
17, respectively.  
The lack of metalization on the outer layers as well as the  
limited thermal connection ensured that heat transfer from  
the converter to the PWB was minimized. This provides a  
worst-case but consistent scenario for thermal derating pur-  
poses.  
All measurements requiring airflow were made in Power-  
One’s vertical and horizontal wind tunnel facilities using In-  
frared (IR) thermography and thermocouples for thermome-  
try.  
Start-up  
Output voltage waveforms, during the turn-on transient using  
the ON/OFF pin for full rated load currents (resistive load)  
are shown without and with 10,000 µF load capacitance in  
Figs. 18 and 19, respectively.  
Ensuring components on the converter do not exceed their  
ratings is important to maintaining high reliability. If one an-  
ticipates operating the converter at or close to the maximum  
loads specified in the derating curves, it is prudent to check  
actual operating temperatures in the application. Thermo-  
graphic imaging is preferable; if this capability is not avail-  
able, then thermocouples may be used. Power-One recom-  
mends the use of AWG #40 gauge thermocouples to ensure  
measurement accuracy. Careful routing of the thermocouple  
leads will further minimize measurement error. Refer to Fig-  
ure 28 for optimum measuring thermocouple location.  
Ripple and Noise  
Figure 22 shows the output voltage ripple waveform, meas-  
ured at full rated load current with a 10 µF tantalum and 1 µF  
ceramic capacitor across the output. Note that all output  
voltage waveforms are measured across a 1 µF ceramic ca-  
pacitor.  
The input reflected ripple current waveforms are obtained  
using the test setup shown in Fig 23. The corresponding  
waveforms are shown in Figs. 24 and 25.  
Thermal Derating  
Load current vs. ambient temperature and airflow rates are  
given in Figs. 10-13. Ambient temperature was varied be-  
JUN 01, 2003 revised to NOV 22, 2006  
Page 8 of 14  
www.power-one.com  

与Q24T15050-NBA0G相关器件

型号 品牌 描述 获取价格 数据表
Q24T15050-NBC0G BEL DC-DC Regulated Power Supply Module, 1 Output, Hybrid,

获取价格

Q24T15050-NCA0 BEL DC-DC Regulated Power Supply Module, 1 Output, Hybrid,

获取价格

Q24T15050-NCA0G BEL DC-DC Regulated Power Supply Module, 1 Output, Hybrid,

获取价格

Q24T15050-NCC0G BEL DC-DC Regulated Power Supply Module, 1 Output, Hybrid

获取价格

Q24T15050-NDBP BEL DC-DC Regulated Power Supply Module, 1 Output, 75W, Hybrid, QUARTER BRICK PACKAGE-8

获取价格

Q24T15050-NDC0 BEL DC-DC Regulated Power Supply Module, 1 Output, Hybrid

获取价格