CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Radial Lead Type, Standard
PLF
Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
PLG
Lead free flow soldering condition correspondence.
Higher
Compliant to the RoHS directive (2011/65/EU).
Capacitance
Long Life
Low ESR
PLS
PLE
PLF
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
–55 to +105°C
2.5 to 25V
Rated Capacitance Range
Capacitance Tolerance
6.8 to 1500µF
20% at 120Hz, 20°C
Less than or equal to the specified value 120Hz, 20°C
Tangent of loss angle (tan δ)
at
(
1)
ESR
Less than or equal to the specified value 100kHz, 20°C
at
Leakage Current ( 2)
Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z–55°C / Z+20°C 1.25
(100kHz)
(
)
)
Capacitance change
Within 20% of the initial capacitance value
3
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Endurance
(
1)
ESR
Leakage current ( 2)
(
3
Capacitance change
Within 20% of the initial capacitance value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Damp Heat
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
(
1)
ESR
(Steady State)
Leakage current ( 2)
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
(
)
3
Capacitance change
Within 10% of the initial capacitance value
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
tan δ
Resistance to
Soldering Heat
(
1)
ESR
Leakage current ( 2)
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 4V 560 F)
µ
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9 10 11 12
Voltage(g:4V)
P L F 0 G 5 6 1 M D O 1
Size code
Configuration
Capacitance tolerance ( 20%)
φd
Series
Lot. No.
Rated capacitance
(
560µF
)
)
+0.5MAX.
15MIN
4MIN
L
Rated voltage
(4V
Series name
Type
(mm)
Size
φD
L
P
φd
φ6.3 × 6L φ6.3 × 9L φ6.3
×
10.5L φ8 × 7L φ8 × 9L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 13L
6.3
5.5
6.3
8.5
2.5
0.6
6.3
10.0
2.5
8.0
6.5
3.5
0.6
8.0
8.5
3.5
0.6
8.0
11.5
3.5
10.0
7.5
10.0
9.5
10.0
12.5
5.0
Voltage
V
2.5
e
4
g
6.3 10 16 20 25
2.5
5.0
5.0
Code
j
A
C
D
E
0.45
0.5
0.6
0.6
0.6
0.6
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
50
CAT.8100E
5秒后页面跳转
TJA1050资料数据分析、引脚说明、应用示例介绍
DS3231时钟芯片：参数分析、引脚说明、应用示例介绍
AD620资料手册解读：引脚说明及功能介绍、参数分析
AT89C52资料手册：引脚说明、参数解读、LED流水灯控制程序示例
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
