SMT Power Inductors
Round Wire Coils– PG0936NL series
Inductance Range: 0.47uH to 25.0uH
Current Rating: up to 40Apk
Footprint: 17.5mm x 16.7mm Max
Height: 10.0mm Max
No Thermal Aging
Electrical Specifications @ 25°C — Operating Temperature -40°C to +130°C 1
Saturation 5
Controlled Electrical Specs.
Current Isat
Inductance 2
@ Irated
(μH Typical)
Heating Current 6
Irated 3
(A)
Core Loss Factor 7
(A TYP)
Part Number
Idc
DCR 4
(mΩ)
MAX
Inductance
@ 0Adc
(μH ± 20%)
(K2)
(A TYP)
25°C
100°C
PG0936.471NL
PG0936.681NL
PG0936.851NL
PG0936.162NL
PG0936.282NL
PG0936.452NL
PG0936.682NL
PG0936.113NL
PG0936.183NL
PG0936.253NL
0.47
0.60
0.74
1.4
2.5
3.6
5.4
8.8
15.4
23.5
40
40
40
31
24
22
18
14
9.8
7.0
0.87
0.87
0.87
1.5
2.2
2.9
3.5
7.0
13.8
19.4
0.47
0.68
0.85
1.6
2.8
4.5
80
62
50
36
28
22
18
14
11
9.2
65
48
40
30
23
18
15
11.5
9
40
40
40
31
24
22
21
14
9.8
7.0
20.0
29.0
36.3
45.5
59.8
76.9
96.8
117.5
153.8
178.0
6.8
11.0
18.0
25.0
8
Notes:
1. Actual temperature of the component during system operation (ambient plus temperature rise) must be
within the standard operating range.
2. Inductance at Irated is a typical inductance value for the component taken at rated current.
3. The rated current as listed is either the saturation current (@ 25°C) or the heating current depending on
which value is lower.
7. Core loss approximation is based on published core data:
Core Loss = K1 * (f)1.72 * (K2ΔI)2.41 in mW
K1 = 8.68E-10
f = switching frequency in KHz
K1 & K2 = core loss factors
4. The DCR of the part is measured at an ambient temperature of 20°C 3°C from point a to b as shown below on
the mechanical drawing.
ΔI= delta I across the component in Ampere
K2ΔI=one half of the peak to peak flux density across the component in Gauss
5. The saturation current, Isat, is the current at which the component inductance drop by 20% (typical) at an
ambient temperature. This current is determined by placing the component in the specified ambient envi-
ronment and applying a short duration pulse current (to eliminate self-heating effect) to the component.
6. The heating current, Idc, is the DC current required to raise the component temperature by approximately
40°C. The heating current is determined by mounting the component on a typical PCB and applying current
for 30 minutes. The temperature is measured by placing the thermocouple on top of the unit under test. Take
note that the components’ performance varies depending on the system condition. It is suggested that the
component be tested at the system level, to verify the temperature rise of the component during system
operation.
8. Unless otherwise specified, all testing is made at 100kHz, 0.1Vac
9. Optional Tape & Reel packaging can be ordered by adding a “T” suffix to the part number (i.e. PG0936.682NL
becomes PG0936.682NLT). Pulse complies with industry standard tape and reel specification EIA481. The tape
and reel for this product has a width (W=32.0mm), pitch (Po=24.0mm) and depth (Ko=10.8mm).
10. The core is a conductive material so care should be taken when mounting this component over an exposed
via or if the voltage across the terminals exceeds 24V. Trickle current through the core material may gener-
ate additional losses and potential overheating. Please contact Pulse to discuss an alternative solution if
required.
Mechanicals
Schematics
.098
[2.50]
PG0936.XXXNL
.689MAX
[17.50]
1
3
.098
[2.50]
2
3
PULSE
PG0936.XXXNL
DATE CODE
CTRY MFG
.657MAX
[16.70]
.118 0.012
[3.00 0.30]
H MAX
(Xꢀ
CORE SLOT
PIN3 IS MECHANICAL SUPPORT ONLY
HAS NO INTERNAL ELECTRICAL CONNECTION
2
1
a
b
FRONT VIEW
d
.005[.13]
TOP VIEW
.449 .020
[11.40 0.50]
3 SURFACES
PART NUMBER
PG0936.471NL
X
0.5ꢀ
Height
H
.197
[5.00]
BOTTOM VIEW
(
.177
[4.50]
2.5
PG0936.681NL
PG0936.851NL
PG0936.162NL
PG0936.282NL
PG0936.452NL
2.5
2.5
2.5
.315[8.0]
Weight...........................9.8 grams
Tape and Reel....................200/tray
.496
[12.60]
.197
[5.00]
2.5
2.5
2.5
1.4
Inches
Dimensions:
mm
PG0936.682NL
PG0936.113NL
PG0936.183NL
PG0936.253NL
.394[10.0]
.157
[4.00]
.010
0,25
Unless otherwise specified, all tolerences are ±
.449
[11.40]
1.4
1.4
SUGGESTED LAND PAT TERN
(REFERENCE ONLYꢀ
http://www.power.pulseelectronics.com/contact
power.pulseelectronics.com
P730.C (05/17)
1