Datasheet > PCA8575DB,112

PCA8575DB,112

更新时间： 2024-01-27 08:00:45

品牌	Logo	应用领域
恩智浦 - NXP		PC
页数	文件大小	规格书
30页	181K
描述
PCA8575 - Remote 16-bit I/O expander for I2C-bus with interrupt SSOP2 24-Pin

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

PCA8575DB,112 数据手册

PCA8575

NXP Semiconductors

Remote 16-bit I/O expander for I²C-bus with interrupt

8. I/O programming

8.1 Quasi-bidirectional I/O architecture

The PCA8575’s 16 ports (see Figure 2) are entirely independent and can be used either

as input or output ports. Input data is transferred from the ports to the microcontroller in

the Read mode (see Figure 12). Output data is transmitted to the ports in the Write mode

(see Figure 11).

Every data transmission from the PCA8575 must consist of an even number of bytes, the

ﬁrst byte will be referred to as P07 to P00, and the second byte as P17 to P10. The third

will be referred to as P07 to P00, and so on.

This quasi-bidirectional I/O can be used as an input or output without the use of a control

signal for data directions. At power-on the I/Os are HIGH. In this mode only a current

source (I_OH) to V_DDis active. An additional strong pull-up to V_DD(I_trt(pu)) allows fast rising

edges into heavily loaded outputs. These devices turn on when an output is written HIGH,

and are switched off by the negative edge of SCL. The I/Os should be HIGH before being

used as inputs. After power-on, as all the I/Os are set HIGH, all of them can be used as

inputs. Any change in setting of the I/Os as either inputs or outputs can be done with the

Write mode.

Remark: If a HIGH is applied to an I/O which has been written earlier to LOW, a large

current (I_OL) will ﬂow to V_SS

8.2 Writing to the port (Output mode)

To write, the master (microcontroller) ﬁrst addresses the slave device. By setting the last

bit of the byte containing the slave address to logic 0 the Write mode is entered. The

PCA8575 acknowledges and the master sends the ﬁrst data byte for P07 to P00. After the

ﬁrst data byte is acknowledged by the PCA8575, the second data byte P17 to P10 is sent

by the master. Once again, the PCA8575 acknowledges the receipt of the data. Each 8-bit

data is presented on the port lines after it has been acknowledged by the PCA8575.

The number of data bytes that can be sent successively is not limited. After every two

bytes, the previous data is overwritten.

The ﬁrst data byte in every pair refers to Port 0 (P07 to P00), whereas the second data

byte in every pair refers to Port 1 (P17 to P10). See Figure 10.

first byte

second byte

07 06 05 04 03 02 01 00

P07 P06 P05 P04 P03 P02 P01 P00

17 16 15 14 13 12 11 10

P17 P16 P15 P14 P13 P12 P11 P10

002aab634

Fig 10. Correlation between bits and ports

PCA8575_2

Product data sheet

Rev. 02 — 21 March 2007

7 of 30

1...4 5 678 9 10...30

下载PDF

与PCA8575DB,112相关器件

型号	品牌	描述	获取价格	数据表
PCA8575DB,118	NXP	PCA8575 - Remote 16-bit I/O expander for I2C-bus with interrupt SSOP2 24-Pin	获取价格
PCA8575DK	NXP	Remote 16-bit I/O expander for I2C-bus with interrupt	获取价格
PCA8575PW	NXP	Remote 16-bit I/O expander for I2C-bus with interrupt	获取价格
PCA8575PW,118	NXP	PCA8575 - Remote 16-bit I/O expander for I2C-bus with interrupt TSSOP2 24-Pin	获取价格
PCA8576C	NXP	Universal LCD driver for low multiplex rates	获取价格
PCA8576CH	NXP	Automotive LCD driver for low multiplex rates	获取价格