NT3966
TFT LCD Source Driver
Pin Description
Description
Designation I/O
D05 ~ D00
D15 ~D10
D25 ~ D20
Data input. For six 6-bit data,2 pixels, of color data (R, G, B)
DX5 : MSB; DX0 : LSB
I
D35 ~ D30
D45 ~ D40
D55 ~ D50
REV1
I
Controls whether the data of D00~D25 are inverted or not.
When “REV1”=1 these data will be inverted. EX. “00” à“ 3F”, “07”à“ 38”, “15” à“2A”, and so on.
Controls whether the data of D30~D55 are inverted or not, same as REV1.
Clock input; latching data onto the line latches at the rising edge.
Gamma correction reference voltage. The voltage of these pins must be AVSS< V10< V9<
V8<V7<V6; V5<V4<V3<V2<V1< AVDD
REV2
CLK
V1 ~ V10
I
I
I
OUT1 ~
OUT420
SHL
O
I
Output drive signals;
Selects left or right shift;
SHL=“1” : DIO1→OUT1,2,3,4,5,6→OUT7,8,9,10,11,12--→OUT415,416,417,418,419,420= DIO2
SHL=“0” : DIO1=OUT1,2,3,4,5,6←OUT7,8,9,10,11,12←-- OUT415,416,417,418,419,420←DIO2
SHL
DIO1
DIO2
SHIFT
1
0
Input
Output
Output
Input
Right
Left
DIO1
DIO2
I/O Start pulse signal input/output
When SHL is applied high (SHL="1"), a start high-pulse on DIO1 is latched at the rising edge of the
CLK. Then the data are latched serially onto internal latches at the rising edge of the CLK. After all
line latches are filled with data, 70 clocks, a pulse is shifted out through the DIO2 pin at the rising
edge of the CLK. This function can cascade two or more devices for dot-size expansion. In normal
applications, the DIO2 signal of the first device is connected to the DIO1 of the second stage, the
DIO2 of the second one is connected to the DIO1 of the third, and so on, ina chain.
In contrast, when SHL is applied low, a start pulse inputs on DIO2, and a pulse outputs through
DIO1.
*Remark: The input pulse-width of DIO1/2 may exceed 1 clock-cycle.
Latches the polarity of outputs and switches the new data to outputs.
1. At the rising edge, the pin latches the “POL” signal to control the polarity of the outputs.
2. The pin also controls the switch of the line registers that switches the new incoming data
to outputs.
*Remark: The LD may switch the new data to outputs at anytime even if the line data are not
completely full.
Polarity selector for the dot-inversion control. Available at the rising edge of LD
LD
I
I
POL
“POL” value is latched at the rising edge of “LD” to control the polarity of the even or odd outputs.
“POL=1” indicates that even outputs are of positive polarity with a voltage range from V1~V5, and
odd outputs are of negative polarity with a voltage range from V6 to V10. On the other hand, if LD
receives low level “POL”, even outputs are of negative polarity and odd outputs are of positive
polarity.
POL=1: Even outputs range from V1 ~ V5
Odd outputs range from V6 ~ V10
POL=0: Even outputs range from V6 ~ V10
Odd outputs range from V1 ~ V5
Power supply for analogcircuit
Ground pin for analog circuit
Power supply for digital circuit
Ground pin for digital circuit
AVDD
AVSS
Vcc
I
I
I
I
GND
Version 1.0
3
DEC 7 ,2001
5秒后页面跳转
一文带你解读74HC244资料手册：特性、应用场景、封装方式、引脚配置说明、电气参数、推荐替代型号
AD623资料手册解读：特性、应用、封装、引脚功能及电气参数
RT9193资料手册解读：RT9193引脚功能、电气参数、替换型号推荐
VIPER22A的资料手册解读、引脚参数说明、代换型号推荐
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
