NOTES:
MMSDX-XX-XXX-X-XX.XX-X-X-XXX
REVISION AL
C
1.
REPRESENTS A CRITICAL DIMENSION.
FEP CABLE OPTION
2. BURR ALLOWANCE: .003[.08] MAX.
3. PARTS TO BE MOLDED TO POSITION.
4. MINIMUM PIN PULLOUT FORCE: 4.000LB[17.79N]
5. CONTACT MUST BE INSERTED UNTIL RETENTION
FEATURE LOCKS INTO PLACE.
-T: FEP INSULATION
(LEAVE BLANK FOR STANDARD
PVC INSULATION)
OPTION
SINGLE
DO NOT
SCALE FROM
THIS PRINT
-M: METAL LATCH (USE IPD1-XX-D-X-M)
No OF POSITIONS
-02 THRU -25
(PER ROW)
WIRE GAUGE (AWG)
PVC: -20, -22, -24, -26, -28, -30
FEP: -20,-24-28-30
(LEAVE BLANK FOR PLASTIC)
6. ALL FINISHED GOODS ARE TO BE ELECTRICAL TESTED INCLUDING HI-POT TEST
@ 1000 VOLTS DC. AFTER FINAL ELECTRICAL TEST, LABEL EACH ASSEMBLY
WITH 1 LABEL-ET. C
DOUBLE
-LUS: PLASTIC LATCH UP, STRAIGHT
-LDS: PLASTIC LATCH DOWN, STRAIGHT
-LUX: PLASTIC LATCH UP, CROSSED
-LDX: PLASTIC LATCH DOWN, CROSSED
-MUS: METAL LATCH UP, STRAIGHT
-MDS: METAL LATCH DOWN, STRAIGHT
-MUX: METAL LATCH UP, CROSSED
-MDX: METAL LATCH DOWN, CROSSED
7. TINNED COPPER WIRE IS ROHS COMPLIANT.
8. PARTS ARE TO BE LAYER PACKAGED.
9. MINIMUM METAL LATCH RETENTION FORCE: 1.000LB[4.45N]
10. REFER TO CRIMP SPECIFICATIONS PRINT FOR CRIMP AND STRIP
DIMENSIONS, TOLERANCES, TOOLING AND ITS REQUIREMENTS.
COLOR CODE
C (SEE TABLE 3, SHEET 3)
(LEAVE BLANK FOR STANDARD
BLACK CABLE)
11. FOR LENGTHS LESS THAN 12 IN, TOLERANCE SHALL
BE ±.125[3.18]. FOR OTHER LENGTHS, TOLERANCES SHALL BE ±2%.
12. LOCATION OF GATE PAD IS AT THE DISCRETION OF THE VENDOR.
13. GOLD PLATING IS NOT REQUIRED ON THE OUTSIDE OF THE CONTACT
BOX OR ON THE SIDE WITH THE RETENTION LANCE.
(NOT AVAILABLE WITH FEP OPTION)
PLATING SPECIFICATION
POLARIZATION OPTION
(-P, -K, OR -G OPTION IS REQUIRED.)
-P: POLARIZATION (SEE FIG 3, SHEET 2)
(NOT AVAILABLE WITH -LUS, -LDS, -LUX, -K, -G OPTIONS)
-K: KEYED POLARIZATION
-F: FLASH SELECTIVE (USE C-179-XX-F)
-L: LIGHT SELECTIVE (USE C-179-XX-L)
-S: SELECTIVE (USE C-179-XX-S)
(No OF POS x .100[2.54])
+ .055[1.40] REF
C
ASSEMBLED LENGTH
(USE IPD1-XX-D-K) (SEE FIG 4, SHEET 2)
(NOT AVAILABLE WITH -P, -G OPTIONS)
-G: GUIDE POST
C
05
10
01
06
SPECIFY IN INCHES [USE DWC-XX-XX]
(SINGLE END: 03.00 INCH MINIMUM,
DOUBLE END: 03.25 INCH MINIMUM)
(USE IPD1-XX-D-GP) (SEE FIG 6, SHEET 3)
(NOT AVAILABLE WITH -LDS, -LUX, -P, -K OPTIONS)
.353 8.97
REF
.250 6.35
REF
END OPTION
-S: SINGLE END
-D: DOUBLE END
(LEAVE BLANK FOR NO POLARIZATION;
AVAILABLE TO EXISTING CUSTOMERS ONLY)
(MUST CHOOSE FROM
LUS, LDS, LUX, LDX, MUS,
MDS, MUX, OR MDX)
IPD1-XX-D
"A"
.100 2.54
REF
C
.505 12.83
REF
.285 7.24
REF
XX.XX
(SEE NOTE 11)
C
C
XX.XX
(SEE NOTE 11)
FIG 1
MMSD-05-22-X-XX.XX-S SHOWN
SECTION "A"-"A"
"A"
FIG 2
MMSD-05-22-X-XX.XX-D SHOWN
PROPRIETARY NOTE
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DECIMALS
ANGLES
2
.XX: .01 [.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
.XXX: .005 [.13]
.XXXX: .0020 [.051]
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 1:0.666667 DESCRIPTION:
.100[2.54] SOCKET DISCRETE CABLE ASSEMBLY
HOUSING: NYLON 66, COLOR: WHITE
CONTACT: PHOS BRONZE
DWG. NO.
CABLE; INSULATION: SEE CALLOUT
WIRE: TINNED COPPER
MMSDX-XX-XXX-X-XX.XX-X-X-XXX
LATCH: NICKEL-PLATED BeCu, #25, 1/2 HT
F:\DWG\MISC\MKTG\MMSDX-XX-XXX-X-XX.XX-X-X-XXX-MKT.SLDDRW
BY:
DEAN P
07/16/2004 SHEET 1 OF 3
5秒后页面跳转
SG3525资料手册详解：SG3525参数分析、引脚说明、应用介绍
AT89C51单片机资料手册详细解析及应用示例
CP2102资料手册解读：CP2102引脚说明、关键参数分析
资料手册解读：UC3842参数和管脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
