Datasheet > MIC4685WRTR

MIC4685WRTR

更新时间： 2024-01-11 09:22:24

品牌	Logo	应用领域
麦瑞 - MICREL		开关
页数	文件大小	规格书
17页	331K
描述
SWITCHING REGULATOR, 225kHz SWITCHING FREQ-MAX, PSSO7, ROHS COMPLIANT, SPAK-7

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

MIC4685WRTR 技术参数

是否无铅：	不含铅	是否Rohs认证：	符合
生命周期：	Transferred	零件包装代码：	MODULE
包装说明：	,	针数：	7
Reach Compliance Code：	compliant	ECCN代码：	EAR99
HTS代码：	8542.39.00.01	风险等级：	5.15
模拟集成电路 - 其他类型：	SWITCHING REGULATOR	控制模式：	VOLTAGE-MODE
控制技术：	PULSE WIDTH MODULATION	最大输入电压：	30 V
最小输入电压：	4 V	标称输入电压：	12 V
JESD-30 代码：	R-PSSO-G7	JESD-609代码：	e3
长度：	9.395 mm	湿度敏感等级：	3
功能数量：	1	端子数量：	7
最高工作温度：	125 °C	最低工作温度：	-40 °C
封装主体材料：	PLASTIC/EPOXY	封装形状：	RECTANGULAR
封装形式：	SMALL OUTLINE	峰值回流温度（摄氏度）：	260
认证状态：	Not Qualified	座面最大高度：	2.03 mm
表面贴装：	YES	切换器配置：	BUCK
最大切换频率：	225 kHz	温度等级：	AUTOMOTIVE
端子面层：	Matte Tin (Sn)	端子形式：	GULL WING
端子节距：	1.27 mm	端子位置：	SINGLE
处于峰值回流温度下的最长时间：	40	宽度：	8 mm
Base Number Matches：	1

MIC4685WRTR 数据手册

Micrel, Inc.

MIC4685

Bootstrap (BS, Pin 1)

Detailed Pin Description

The bootstrap pin, in conjunction with the external

bootstrap capacitor, provides a bias voltage higher than

the input voltage to the MIC4685’s main NPN pass

element. The bootstrap capacitor sees the dv/dt of the

switching action at the SW pin as an AC voltage. The

bootstrap capacitor then couples the AC voltage back to

the BS pin, plus the dc offset of V_INwhere it is rectiﬁed and

used to provide additional drive to the main switch; in this

case, a NPN transistor.

Switch (SW, Pin 6)

The switch pin is tied to the emitter of the main internal

NPN transistor. This pin is biased up to the input voltage,

minus the V_SAT, of the main NPN pass element. The

emitter is also driven negative when the output inductor’s

magnetic ﬁeld collapses at turn-off. During the OFF time,

the SW pin is clamped by the output Schottky diode

typically to a –0.5V.

This additional drive reduces the NPN’s saturation voltage

and increases efﬁciency, from a V_SATof 1.8V, and 75%

Ground (GND, Pin 4, Tab)

There are two main areas of concern when it comes to the

ground pin, EMI and ground current. In a buck regulator or

any other non-isolated switching regulator, the output

capacitor(s) and diode(s) ground is referenced back to the

switching regulator’s or controller’s ground pin. Any

resistance between these reference points causes an

offset voltage/IR drop proportional to load current and poor

load regulation. This is why it’s important to keep the

output grounds placed as close as possible to the

switching regulator’s ground pin. To keep radiated EMI to

a minimum, it is necessary to place the input capacitor

ground lead as close as possible to the switching

regulator’s ground pin.

efﬁciency to

respectively.

a V_SATof 0.5V and 88% efﬁciency

Feedback (FB, Pin 3)

The feedback pin is tied to the inverting side of an error

ampliﬁer. The noninverting side is tied to a 1.235V

bandgap reference. An external resistor voltage divider is

required from the output-to-ground, with the center tied to

the feedback pin. See Tables 1 and 2 for recommended

resistor values.

Enable (EN, Pin 5)

The enable (EN) input is used to turn on the regulator and

is TTL compatible. Note: connect the enable pin to the

input if unused. A logic-high enables the regulator. A logic-

low shuts down the regulator and reduces the stand-by

quiescent input current to typically 150µA. The enable pin

has an up-per threshold of 2.0V minimum and lower

threshold of 0.8V maximum. The hysterisis provided by the

upper and lower thresholds acts as an UVLO and prevents

unwanted turn on of the regulator due to noise.

Input Voltage (V_IN, Pin 2)

The V_INpin is the collector of the main NPN pass element.

This pin is also connected to the internal regulator. The

output diode or clamping diode should have its cathode as

close as possible to this point to avoid voltage spikes

adding to the voltage across the collector.

M9999-012610

January 2010

1 234 5 6 7...17

下载PDF

与MIC4685WRTR相关器件

型号	品牌	描述	获取价格	数据表
MIC4685WR-TR	MICREL	SWITCHING REGULATOR, 225kHz SWITCHING FREQ-MAX, PSSO7	获取价格
MIC4685YR	MICROCHIP	SWITCHING REGULATOR, 225kHz SWITCHING FREQ-MAX, PSSO7	获取价格
MIC4690	MICREL	500kHz 1A SuperSwitcher Buck Regulator	获取价格
MIC4690	MICROCHIP	The MIC4690 SuperSwitcher? is an easy-to-use, 500kHz step-down PWM voltage regulator. Th	获取价格
MIC4690_05	MICREL	500kHz 1A SuperSwitcher Buck Regulator	获取价格
MIC4690BM	MICREL	500kHz 1A SuperSwitcher Buck Regulator	获取价格

与MIC4685WRTR相关文章

PCF8574资料解读：主要参数分析、引脚说明
2024-05-21

10
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
2024-05-21

9
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
2024-05-21

12
一文带你了解压敏电阻器在直流电路中的过压保护作用
2024-05-21

7

产品中心

服务支持

精选活动

关于我们

帮助中心

MIC4685WRTR

MIC4685WRTR 技术参数

MIC4685WRTR 数据手册

与MIC4685WRTR相关器件

与MIC4685WRTR相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

MIC4685WRTR

MIC4685WRTR 技术参数

MIC4685WRTR 数据手册

与MIC4685WRTR相关器件

与MIC4685WRTR相关文章

您还可以找

您在本页遇到什么问题？