MG100
1W, Miniature DIP
1 kV To 6 kV Isolation,
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
● 1W Output Power
● 1 kV to 6kV Isolation
● 80 Standard Models
● Single & Dual Outputs
● Miniature DIP Case
● EN 62368 Approved
● Efficiency to 86%
● -40°C to +85°C Operation
● Industry Standard Pin-Out
● Low Cost!
Parameter
Conditions
3.3 VDC Input 2.97
5 VDC Input 4.5
Min.
Typ.
3.3
5.0
12.0
15.0
24.0
Max.
3.63
5.5
13.2
16.5
26.4
Units
Input Voltage Range
12 VDC Input 10.8
15 VDC Input 13.5
24 VDC Input 21.6
Capacitor Filter
VDC
Input Filter
Output
Parameter
Conditions
Min.
Typ.
Max.
± 3.0
Units
%
%
Output Voltage Accuracy
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Temperature Coefficient
Output Short Circuit
General
For VIN Change of 1%
See Note 1
± 1.2
± 10
75
%
mV P - P
%/°C
± 0.02
Momentary (0.5 Sec)
Parameter
Conditions
Min.
See Page 3
1,000
Typ.
Max.
Units
Isolation Voltage, 60 Sec
Isolation Resistance
Isolation Capacitance
Switching Frequency
EMI Characteristics
Parameter
MΩ
pF
kHz
60
80
Standard
Criteria
Level
Radiated Emissions
Conducted Emissions
ESD
RS
EFT
Surge
CS
PFMF
EN 55032
EN 55032
Class B
Class B
± ± kV/± ꢀkV
ꢁꢂV/m
See Note 3
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
A
A
A
A
A
A
See Note 4
See Note 4
± ꢃ kV
± ꢂ.ꢄ kV
ꢁꢂ Vrms
ꢁA/m
Environmental
Parameter
Conditions
Min.
-40
Typ.
+25
Max.
Units
°C
Ambient
Case
+85
+100
+125
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
-40
°C
Free Air Convection
RH, Non-condensing
95
%
Physical
Case Size
See Mechanical Diagrams (Page 7)
Case Material
Weight
Non-Conductive Black Plastic (UL94-V0)
See Mechanical Diagrams (Page 7)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
Reliability Specifications
Parameter
Conditions
MIL HDBK 217F, 25°C, Gnd Benign 1.121
UL/cUL 62368 recognition (UL certificate)
Min.
Typ.
Max.
Units
MHours
MTBF
Safety Standards
Absolute Maximum Ratings
Parameter
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Conditions
3.3 VDC Input
Min.
Typ.
Max.
6.0
7.0
15.0
18.0
28.0
260
Units
VDC
°C
5 VDC Input
12 VDC Input
15 VDC Input
Input Voltage Surge (0.1 Sec)
24 VDC Input
Lead Temperature
1.5 mm From Case for 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com