LME78_1.0 series
Wide Input Non-Isolated & Regulated, Single Positive/Negative Output
Switching Regulator
High efficiency up to 96%
Operating temperature range:
-40°C ~ +85°C
Short circuit protection (SCP)
No-load input current as low
as 0.3mA
3PIN SIP package
The LME78_1.0 are high efficiency switching regulators and ideal
substitutes of LM78xx series three-terminal linear regulators. The
product is featured with high efficiency, low loss, short circuit protection
and no heat sink requirement. They are widely used in industrial control,
instrumentation, and electric power applications.
Non isolated, no need for
heatsink
UL94V-0 package material
IEC62368, UL62368, EN62368
approved
UL-62368-1 (E347551)
Common specifications
Short circuit protection:
No-load input current:
Temperature rise at full load:
Cooling:
Output specifications
Hiccup, automatic recovery
2mA TYP, 5mA MAX
25°C MAX, 15°C TYP
Item
Test conditions
Min
Typ
Max
Units
Voltage accuracy
Full load, input voltage
range
• LME78_03-1.0
• Others
2
1.5
4
3
%
%
Free air convection
Line regulation
Load regulation
Full load, input voltage
range
0.2
0.4
%
Operation temperature range:
-40°C~+85°C
(see temperature derating curve)
10% to 100% load
• positive output
• negative output
Storage temperature range:
Pin welding resistance temperature:
Operating case temperature:
Storage humidity range:
Package material:
-55°C ~+125°C
0.4
0.4
0.6
0.8
%
%
260°C MAX, 1.5mm from case for 10 sec
100°C
Ripple + Noise*
20MHz bandwidth,
nominal input, 20%
-100% load
25
75
mVp-p
< 95%RH
Plastic [UL94-V0]
2000 K hours
1.9g
Switching frequency
520
KHz
MTBF (MIL-HDBK-217F @25°C):
Weight:
Temperature Drift
Coefficient
0.03 %/°C
Transient response
deviation
Nominal input,
60
200
mV
ms
25%-50%-25%, 50%-75%-
50% load step change
Input specifications
Item
Test conditions
Min
Typ
Max
Units
Transient recovery
time
Nominal input,
25%-50%-25%, 50%-75%-
50% load step change
1
No-load input
current
• positive output
• negative output
0.3
1
1
4
mA
mA
Reverse polarity
input
Forbidden
* Test ripple and noise by “parallel cable” method.
With the load lower than 20%, the maximum ripple and noise of 3.3V/5V output
products will be 100mVp-p, 9V/12V/15V output products will be 2%Vo.
Input Filter
Capacitor Filter
* Test ripple and noise by “parallel cable” method.
EMC specifications
Example:
EMI
EMI
EMS
EMS
EMS
CE
CISPR32/EN55032
CISPR32/EN55032
IEC/EN61000-4-2
IEC/EN61000-4-3
IEC/EN61000-4-4
CLASS B
LME78_05-1.0
(see EMC rec. circuit 2 )
LME78 = Series; 05 = 5Vout; 1.0 = 1.0A
RE
CLASS B
(see EMC rec. circuit 2 )
Note:
ESD
RS
Contact 4KV
perf. Criteria A
1. The max. capacitive load should be tested within the input voltage range and
under full load conditions;
10V/m
perf. Criteria A
2. Without any special statement, all indexes are only specific to positive output
application;
3. Unless otherwise specified, data in this datasheet should be tested under the
conditions of Ta = 25°C, humidity <75% when inputting nominal voltage and
outputting rated load;
EFT
1KV
perf. Criteria A
(see EMC rec. circuit 1 )
4. All index testing methods in this datasheet are based on our Company’s
corporate standards;
EMS
EMS
Surge
CS
IEC/EN61000-4-5
IEC/EN61000-4-6
line to line 1KV
perf. Criteria A
5. The performance indexes of the product models listed in this manual are as
above, but some indexes of non-standard model products will exceed the
above-mentioned requirements, and please directly contact with our technician
for specific information;
(see EMC rec. circuit 1 )
3Vr.m.s
perf. Criteria A
6. Specifications subject to change without prior notice.
Page 1 of 4
LME78_1.0 – Rev. 2020-1.1
Specifications subject to change without notice.
GAPTEC-Electronic GmbH & Co. KG
sales@gaptec-electronic.com – www.gaptec-electronic.com