LM4991
www.ti.com
SNAS217A –MAY 2004–REVISED APRIL 2013
(1) (2)
Electrical Characteristics VDD = 5V
The following specifications apply for VDD = 5V and RL = 8Ω unless otherwise specified. Limits apply for TA = 25°C.
LM4991
Parameter
Test Conditions
Units
(Limits)
Typ(3)
Limit(4)
Quiescent Power Supply Current VIN = 0V, no Load
3
4
7
IDD
mA (max)
VIN = 0V, RL = 8Ω
10
2.0
ISD
Shutdown Current
Shutdown Voltage
VSHUTDOWN = VDD
0.1
1.5
1.3
5
µA (max)
V
VSDIH
VSDIL
VOS
V
Output Offset Voltage
35
mV (max)
W (min)
(5)
(5)
THD = 1% (max), f = 1kHz
THD+N = 10%, f = 1kHz
LM4991LD, RL = 3Ω
LM4991LD, RL = 4Ω
LM4991, RL = 8Ω
2.38
2.1
1.3
3
0.9
Po
Output Power
(5)
(5)
LM4991LD, RL = 3Ω
LM4991LD, RL = 4Ω
LM4991, RL = 8Ω
2.5
1.5
0.2
W
THD+N
PSRR
Total Harmonic Distortion+Noise PO = 0.5W, f = 1kHz
%
Power Supply Rejection Ratio
VRIPPLE = 200mV sine p-p,
Input terminated with 10Ω,
f = 1kHz
64
55
dB (min)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics VDD= 5V state DC and AC
electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within
the Operating Ratings. Specifications are not ensure for parameters where no limit is given, however, the typical value is a good
indication of device performance.
(2) All voltages are measured with respect to the ground pin, unless otherwise specified.
(3) Typicals are specified at 25°C and represent the parametric norm.
(4) Limits are ensured to AOQL (Average Outgoing Quality Level).
(5) When driving 3Ω or 4Ω loads from a 5V supply, the LM4991LD must be mounted to a circuit board.
(1) (2)
Electrical Characteristics VDD = 3V
The following specifications apply for VDD = 3V and RL = 8Ω unless otherwise specified. Limits apply for TA = 25°C.
LM4991
Parameter
Test Conditions
Units
(Limits)
Typ(3)
Limit(4)
IDD
Quiescent Power Supply
Current
VIN = 0V, no Load
VIN = 0V, RL = 8Ω
VSHUTDOWN = VDD
3
4
7
7
mA
(max)
ISD
Shutdown Current
0.1
1.1
0.9
5
2.0
µA (max)
VSDIH
VSDIL
VOS
Shutdown Voltage Input High
Shutdown Voltage Input Low
Output Offset Voltage
V
V
35
mV
(max)
Po
Output Power
THD = 1% (max), f = 1kHz
PO = 0.25W, f = 1kHz
RL = 4Ω
RL = 8Ω
600
425
mW
%
Total Harmonic
Distortion+Noise
THD+N
0.1
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics VDD= 5V state DC and AC
electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within
the Operating Ratings. Specifications are not ensure for parameters where no limit is given, however, the typical value is a good
indication of device performance.
(2) All voltages are measured with respect to the ground pin, unless otherwise specified.
(3) Typicals are specified at 25°C and represent the parametric norm.
(4) Limits are ensured to AOQL (Average Outgoing Quality Level).
Copyright © 2004–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM4991