LM4866
www.ti.com
SNAS137E –JULY 2001–REVISED MARCH 2013
Electrical Characteristics for Entire IC(1)(2)
The following specifications apply for VDD= 5V unless otherwise noted. Limits apply for TA= 25°C.
LM4866
Typical(3) Limit(4)
Units
(Limits)
Parameter
Supply Voltage
Test Conditions
VDD
2
V (min)
V (max)
5.5
IDD
ISD
Quiescent Power Supply Current
Shutdown Current
VIN = 0V, IO = 0A(5)
VDD applied to the SHUTDOWN pin
11.5
0.7
20
6
mA (max)
mA (min)
2
μA (max)
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(2) All voltages are measured with respect to the ground (GND) pins unless otherwise specified.
(3) Typicals are measured at 25°C and represent the parametric norm.
(4) Datasheet min/max specification limits are specified by design, test, or statistical analysis.
(5) The quiescent power supply current depends on the offset voltage when a practical load is connected to the amplifier.
Electrical Characteristics for Bridged-Mode Operation(1)(2)
The following specifications apply for VDD= 5V unless otherwise specified. Limits apply for TA= 25°C.
LM4866
Typical(3) Limit(4)
Units
(Limits)
Parameter
Test Conditions
VOS
PO
Output Offset Voltage
Output Power(5)
VIN = 0V
5
50
mV (max)
THD+N = 1%, f = 1kHz(6)
LM4866PWP, RL = 3Ω
LM4866NHW, RL = 3Ω
LM4866PWP, RL = 4Ω
LM4866NHW, RL = 4Ω
LM4866PW, RL = 8Ω
THD+N = 10%, f = 1kHz
LM4866PWP, RL = 3Ω
LM4866NHW, RL = 3Ω
LM4866PWP, RL = 4Ω
LM4866NHW, RL = 4Ω
LM4866PW, RL = 8Ω
2.5
2.5
2.2
2.2
1.1
W
W
W
W
1.0
W (min)
3.2
3.2
2.7
2.7
1.5
W
W
W
W
W
THD+N
PSRR
Total Harmonic Distortion+Noise
Power Supply Rejection Ratio
20Hz ≤ f ≤ 20kHz, AVD = 2
LM4866PWP, RL = 4Ω, PO = 2W
LM4866NHW, RL = 4Ω, PO = 2W
LM4866PW, RL = 4Ω, PO = 1W
0.3
0.3
0.3
LM4866PW, RL = 8Ω, PO = 1W
0.3
67
%
VDD = 5V, VRIPPLE = 200mVRMS, RL = 8Ω,
CB = 1.0μF
dB
XTALK
SNR
Channel Separation
Signal To Noise Ratio
f = 1kHz, CB = 1.0μF
90
98
dB
dB
VDD = 5V, PO = 1.1W, RL = 8Ω
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
(2) All voltages are measured with respect to the ground (GND) pins unless otherwise specified.
(3) Typicals are measured at 25°C and represent the parametric norm.
(4) Datasheet min/max specification limits are specified by design, test, or statistical analysis.
(5) Output power is measured at the device terminals.
(6) When driving 3Ω or 4Ω loads and operating on a 5V supply, the LM4866NHW and LM4866PWP must be mounted to a circuit board that
has a minimum of 2.5in2 of exposed, uninterrupted copper area connected to the package's exposed DAP.
Copyright © 2001–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM4866