Datasheet
LM358xxx LM324xxx LM2904xxx LM2902xxx
LM324F, LM2902F
LM324FJ, LM2902FJ
LM324FV, LM2902FV
: SOP14
: SOP-J14
: SSOP-B14
LM324FVJ, LM2902FVJ : TSSOP-B14J
Pin No.
Pin Name
OUT1
-IN1
1
2
OUT1
1
2
3
4
5
6
7
14
13
12
11
OUT4
-IN4
3
+IN1
VCC
-IN1
+IN1
VCC
+IN2
-IN2
CH1
CH4
4
-
-
+
+
+IN4
VEE
5
+IN2
-IN2
6
7
OUT2
OUT3
-IN3
10 +IN3
8
-
-
+
+
CH2
CH3
9
9
8
-IN3
10
11
12
13
14
+IN3
VEE
OUT2
OUT3
+IN4
-IN4
OUT4
Absolute Maximum Ratings (TA=25°C)
Parameter
Rating
Symbol
Unit
LM358xxx
LM324xxx LM2904xxx LM2902xxx
Supply Voltage
VCC-VEE
36
V
0.68(Note 1,9)
-
0.68(Note 1,9)
SOP8
-
0.67(Note 2,9)
0.62(Note 3,9)
-
0.67(Note 2,9)
0.62(Note 3,9)
-
SOP-J8
SSOP-B8
-
-
0.62(Note 3,9)
0.58(Note 4,9)
0.58(Note 4,9)
-
0.62(Note 3,9)
0.58(Note 4,9)
0.58(Note 4,9)
-
TSSOP-B8
TSSOP-B8J
MSOP8
SOP14
SOP-J14
SSOP-B14
TSSOP-B14J
VID
-
-
Power Dissipation
PD
W
-
-
-
-
-
-
0.56(Note 5,9)
1.02(Note 6,9)
0.87(Note 7,9)
0.85(Note 8,9)
-
-
-
-
0.56(Note 5,9)
1.02 (Note 6,9)
0.87(Note 7,9)
0.85(Note 8,9)
Differential Input Voltage (Note 10)
Input Common-mode Voltage Range
Input Current(Note 11)
36
V
V
VICM
(VEE-0.3) to (VEE+36)
±10
II
mA
Vopr
Operating Supply Voltage
3.0 to 32.0
V
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature
Topr
-40 to +85
-40 to +125
°C
°C
°C
Tstg
-55 to +150
150
Tjmax
(Note 1) Reduce by 5.5mW per 1°C above 25C.
(Note 2) Reduce by 5.4mW per 1°C above 25°C.
(Note 3) Reduce by 5.0mW per 1°C above 25°C.
(Note 4) Reduce by 4.7mW per 1°C above 25°C.
(Note 5) Reduce by 4.5mW per 1°C above 25°C.
(Note 6) Reduce by 8.2mW per 1°C above 25°C.
(Note 7) Reduce by 7.0mW per 1°C above 25°C.
(Note 8) Reduce by 6.8mW per 1°C above 25°C.
(Note 9) Mounted on an FR4 glass epoxy PCB 70mm×70mm×1.6mm (Copper foil area less than 3%).
(Note 10) Differential Input Voltage is the voltage difference between the inverting and non-inverting inputs.
The input pin voltage is set to more than VEE
.
(Note 11) An excessive input current will flow when input voltages of less than VEE-0.6V are applied.
The input current can be set to less than the rated current by adding a limiting resistor.
Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
www.rohm.com
©2015 ROHM Co., Ltd. All rights reserved.
TSZ22111・15・001
TSZ02201-0GMG0G200190-1-2
01.Aug.2016 Rev.005
2/44