Electrical Characteristics (Continued)
+
on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V voltage level (or to ground for a large overdrive) for the time
duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns
to a value greater than −0.3V.
Note 4: These specifications are limited to −55˚C≤T ≤+125˚C, for the LM193/LM193A. With the LM293 all temperature specifications are limited to
A
−25˚C≤T ≤+85˚C and the LM393 temperature specifications are limited to 0˚C≤T ≤+70˚C. The LM2903 is limited to −40˚C≤T ≤+85˚C.
A
A
A
Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so
no loading change exists on the reference or input lines.
Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode
+
+
voltage range is V −1.5V at 25˚C, but either or both inputs can go to 36V without damage, independent of the magnitude of V .
Note 7: The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance
characteristics section.
Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the
comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the magnitude of the negative power supply,
if used).
+
+
Note 9: At output switch point, V .1.4V, R =0Ω with V from 5V to 30V; and over the full input common-mode range (0V to V −1.5V), at 25˚C.
O
S
Note 10: Refer to RETS193AX for LM193AH military specifications and to RETS193X for LM193H military specifications.
Ordering Information
Package
Temperature Range
Part Number
NSC Drawing
*
LM193H
LM193H/883
LM193H-MLS
LM193AH-MLS
−55˚C to 125˚C
**
8-Pin Metal Can
LM193AH-QMLV
LM193AH
H08C
LM193AH/883
LM293H
−25˚C to 85˚C
0˚C to 70˚C
LM393H
*
LM193J/883
LM193AJ/883
8-Pin Ceramic DIP
8-Pin Molded DIP
8-Pin SOIC
−55˚C to 125˚C
J08A
N08E
M08A
**
LM193AJ-QMLV
LM193AJ-MLS
LM393N
0˚C to 70˚C
−40˚C to 85˚C
LM2903N
LM393M
0˚C to 70˚C
−40˚C to 85˚C
0˚C to 70˚C
LM393MX
LM2903M
LM2903MX
LM393TL
LM393TLX
LM2903ITL
LM2903ITLX
8-Bump (12 mils)
micro SMD
TLA08AAA
−40˚C to 85˚C
*
Note: Also available per LM38510/11202
**
Note:
See STD Mil DWG 5962-94526
5
www.national.com