LA6565
Recommended Operating Conditions at Ta = 25°C
Parameter
Supply voltage
Symbol
Conditions
Ratings
Unit
V
V
5.6 to 13
CC
Electrical Characteristics at Ta = 25°C, V 1 = V 2 = 8V, VREF = 2.5V
CC CC
Ratings
typ
Parameter
Symbol
Conditions
Unit
min
max
Overall
Quiescent current when o
Quiescent current when off
I
I
-ON
BTL amplifier output on, loading block off *1
30
10
50
15
mA
mA
°C
CC
-OFF
All outputs off *1
*7
CC
Thermal shutdown circuit
operating temperature
VREF Amplifier
TSD
150
175
200
VREF amplifier offset voltage VREF-OFFSET
-10
1
+10
mV
V
VREF input voltage range
VREF-OUT output current
VREF-IN
V
V
-1.5
CC
I-VREF-OUT
1
mA
Operational Amplifier (Independent)
Input voltage range
V
(OP)
0
2
-1.5
V
IN
CC
Output current (sink)
Output current (source)
Output offset voltage
Residual current (sink)
SINK(OP)
mA
µA
mV
V
SOURCE(OP)
300
-10
500
V
(OP)
OFF
+10
0.6
V -SINK(OP)
CE
I (sink side) = 1mA
O
BTL Amplifier Block (Channels 1 to 4)
Output offset voltage
V
The voltage difference between each channel
outputs *2, *3
-50
+50
-1.5
mV
OFF
Input voltage range
Output voltage
V
V
Input voltage range of the input operational amplifiers
0
V
CC
V
V
IN
+
-
I
= 0.5A, the voltage between V
and V in each
5.7
6.2
8
O
O
O
O
channel
Closed circuit voltage gain
Slew rate SR
VG
SR
V
The gain from the input to the output with the input
amplifier set to 0dB*2, *3
7.2
2.5
9
times
For the independent amplifier. Times 2 when
between outputs.*7
0.5
V/µs
Muting on voltage
Muting off voltage
-ON
The output on voltage, for each mute function *4
V
V
MUTE
V
-OFF
The output off voltage, for each mute function *4
0.5
MUTE
Input Amplifier Block (Channels 1 and 2)
Input voltage range
Output current (sink)
Output current (source)
Output offset voltage
V
-OP
0
2
V
-1.5
V
IN
CC
SINK-OP
mA
µA
mV
SOURCE-OP
*5
300
-10
500
6.5
V
-OP
OFF
+10
Loading Block (Channel 5, H bridge circuit)
Output voltage
V
-LOAD
For forward/reverse operation, I = 0.5A,
O
5.7
V
V
O
VCONT = V
*
CC
The output voltage during braking *6
Braking output saturation
voltage
V
-BREAK
0.3
1
CE
Low-level input voltage
V
V
-L
V
V
IN
High-level input voltage
H
2
IN-
Power Supply Block (Uses an external 2SB632K PNP-transistor)
Power supply output
REG-IN sink current
Line regulation
V
I
= 200mA
O
1.260
5
1.285
10
1.310
V
OUT
REG-IN-SINK
External PNP-transistor base current
6V ≤ V ≤ 12V, I = 200mA
mA
mV
mV
∆V LN
10
100
100
O
CC
O
Load regulation
∆V LD
5mA ≤ I ≤ 200mA
10
O
O
*1: The total current dissipation for V P1, V P2, and V S with no load.
CC
CC
CC
*2: The input amplifier is a buffer amplifier.
*3: The voltage difference between the two sides of the load (12Ω).
*4: When the MUTE pin is high, the output will be on, and when low, the output will be off (high-impedance state).
*5: The input operational amplifier source is constant current. Since the 11kΩ resistor between this and the next stage functions as the load, the input
operational amplifier gain must be set carefully.
*6: The braking operation is a short (to ground) braking operation. The sink side output is on at this time.
*7: Design guarantee.
No.7817-2/8