Datasheet > IM802D-83BFS-137.0000MHZ

IM802D-83BFS-137.0000MHZ

更新时间： 2023-08-15 00:00:00

品牌	Logo	应用领域
ILSI		/
页数	文件大小	规格书
9页	773K
描述
LVCMOS Output Clock Oscillator, 137MHz Nom,

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

IM802D-83BFS-137.0000MHZ 数据手册

浏览型号IM802D-83BFS-137.0000MHZ的Datasheet PDF文件第2页

浏览型号IM802D-83BFS-137.0000MHZ的Datasheet PDF文件第3页

浏览型号IM802D-83BFS-137.0000MHZ的Datasheet PDF文件第4页

浏览型号IM802D-83BFS-137.0000MHZ的Datasheet PDF文件第6页

浏览型号IM802D-83BFS-137.0000MHZ的Datasheet PDF文件第7页

浏览型号IM802D-83BFS-137.0000MHZ的Datasheet PDF文件第8页

MEMS Oscillator, Low Power, LVCMOS, 115.000 MHz to 137.000 MHz

IM802 Series

Pin Functionally

Pin Description

Symbol

Functionality

Pin Assignments

High or Open = specified frequency output

Low = Output is high impedance, only output is disabled.

Tri-state

Standby

High or Open = specified frequency output.

Low = Output is low. Device goes to sleep mode. Supply current

reduces to standby current.

ꢀꢀꢀ

N/C

Vdd

Any voltage between 0.0 V to Vdd or Open = specified frequency

No Connect output

Pin 1 has no functiion

N/C

Top View

GND

Out

Power

Output

Power

Electrical ground

Oscillator output

GND

OUT

Vdd

Power supply voltage

Notes:

ꢀꢀꢀ

1. In OE or ST mode, a pull-up resistor of 10.0 kΩ or less is recommended if Pin 1 is not externally

driven. If Pin 1 needs to be left floating, use the NC option.

2. A capacitor of value 0.1 µF or higher between Pin 4 (Vdd) and Pin 1 (GND) is required.

ꢀꢀꢀꢀ

Pin 1 Configuration Options (OE, or ꢁꢂ, or NC)

Pin 1 of the IM802 can be factory-programmed to support three modes: Output Enable (OE), Standby (ST) or No Connect (NC).

ꢀꢀꢀ

Output Enable (OE) Mode

In the OE mode, applying logic Low to the OE pin only disables the output driver and puts it in Hi-Z mode. The core of the device

continues to operate normally. Power consumption is reduced due to the inactivity of the output. When the OE pin is pulled High, the

output is typically enabled in <1µSec.

ꢀꢀꢀꢀ

Standby ꢁꢂꢃMode

In the ST mode, a device enters into the standby mode when Pin 1 pulled Low. All internal circuits of the device are turned off. The

ꢀꢀꢀ

current is reduced to a standby current, typically in the range of a few µA. When ST is pulled High, the device goes through the

“resume” process, which can take up to 5 mSec.

No Connect (NC) Mode

In the NC mode, the device always operates in its normal mode and outputs the specified frequency regardless of the logic level

on Pin 1.

Table1 below summarizes the key relevant parameters in the operation of the device in OE, ST, or NC mode.

Parameters

Active current 125.0 MHz (max +1.80 VDC)

5.6 mA

OE disable current (max +1.80 VDC)

Standby current (typical +1.80 VDC)

OE enable time at 125.0 MHz (max)

4.0 mA

N/A

0.6 µA

N/A

124 nSec

Resume time from standby

(max, all frequency)

N/A

5 mSec

N/A

Output driver in OE disable/standby mode

High Z

Table 1 OE vs. ST vs. NC

Rev: 08/18/17_B

Page 5 of 9

ILSI America Phone 775-851-8880 ● Fax 775-851-8882 ●email: e-mail@ilsiamerica.com ●

www.ilsiamerica.com

Specifications subject to change without notice

1 2 3 456 7 8 9

下载PDF

与IM802D-83BFS-137.0000MHZ相关器件

型号	品牌	描述	获取价格	数据表
IM802D-83EES-137.0000MHZ	ILSI	LVCMOS Output Clock Oscillator, 137MHz Nom,	获取价格
IM802D-83UFS-137.0000MHZ	ILSI	LVCMOS Output Clock Oscillator, 137MHz Nom,	获取价格
IM802E	ILSI	Direct pin to pin drop-in replacement for industry-standard packages	获取价格
IM802E	MMD	MEMS Oscillator, Low Power, LVCMOS/HCMOS Compatible, 115.000 MHz to 137.000 MHz	获取价格
IM802E-11EFS-115.0000MHZ	ILSI	LVCMOS Output Clock Oscillator, 115MHz Nom,	获取价格
IM802E-11-FS-115.0000MHZ	ILSI	LVCMOS Output Clock Oscillator, 115MHz Nom,	获取价格

产品中心

服务支持

精选活动

关于我们

帮助中心

IM802D-83BFS-137.0000MHZ

IM802D-83BFS-137.0000MHZ 数据手册

与IM802D-83BFS-137.0000MHZ相关器件

与IM802D-83BFS-137.0000MHZ相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

IM802D-83BFS-137.0000MHZ

IM802D-83BFS-137.0000MHZ 数据手册

与IM802D-83BFS-137.0000MHZ相关器件

与IM802D-83BFS-137.0000MHZ相关文章

您还可以找

您在本页遇到什么问题？