SPECIFICATIONS
Specifications are typical at 25OC unless otherwise noted.
Specifications are subject to change without notice.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage VDD
Storage Temperature
-0.5 V to 7.0 V
-55OC to +125OC
Maximum Process Temperature 260OC, 10 seconds
Supply Voltage
1.8V to 5V, as required
Calibration Tolerance
Frequency Stability
+_ 5 ppm minimum and up
+_ 10 ppm and up for Commercial
+_ 20 ppm and up for Industrial
+_ 30 ppm and up for Military
+_ 15 ppm and up for Commercial
+_ 20 ppm and up for Industrial
+_ 35 ppm and up for Military
15 pF
ENABLE / TRI-STATE
1
Over Temperature
PIN 1*
PIN 3
High Z
Low
E
High
Low
Freq. Output
High Z
Total Frequency
2
Tolerance
T
High
NC
Freq. Output
Freq. Output
N
CMOS Load3
Start-up Time
Rise/Fall Time
Duty Cycle
* Normally high (internal pull-up resistor)
10 ms MAX
8 ns MAX
40% MIN, 60% MAX
Shock survival
Vibration survival
Up to 100,000 g peak, 0.5 ms,1/ sine
ENABLE (E) VS. TRI-STATE (T)
2
20 g RMS 10-2000 Hz random
E
When pin 1 is low, the oscillator stops
oscillating.
Standard Operating
Temperature Ranges
-10OC to +70OC (Commercial)
-40OC to +85OC (Industrial)
-55OC to +125OC (Military)
T
When pin 1 is low, the internal oscillator
continues to run, however, the output (pin 3)
is in a high impedance (Z) state.
E
T
1. Does not include calibration tolerances.
2. Frequency over temperature relative to nominal frequency.
3. TTL loads and higher CMOS loads available. Contact factory.
Current consumption
when pin 1 is low
Very
Low
Lower than
Normal
Output recovery delay
when pin 1 changes from
low to high
Delayed Immediate
PACKAGING OPTIONS
HGXO - Tray Pack
- Tape and Reel
(Reference tape and reel data sheet 10109)
HOW TO ORDER HGXO SURFACE MOUNT CRYSTAL OSCILLATORS
HGXO
3
D
S
T
SM3
20.0M
,
30
/
50
/
/
I
Supply Voltage Shock Level
“S” if special
or custom
design.
E = Enable Blank =SM1
Frequency
K = kHz
M = MHz
Frequency
Stability over
Temp.Range
(in ppm)
Calibration
Tolerance
@ 250C
Temp. Range:
1 = 1.8V
2 = 2.5V
3 = 3.0V
4 = 3.3V
5 = 5.0V
A = 5,000 g
C
I
= -10OC to +70OC
T = Tri-State
=Gold Plated
B = 10,000 g
C = 20,000 g
D = 30,000 g
F = 50,000 g
G = 75,000 g
H = 100,000 g
N = Neither SM3 =Gold Plated +
Solder Dipped
= -40OC to +85OC
Blank if Std.
M = -55OC to +125OC
(in ppm)
S
= Customer Specified
OR
/
/
100
/
I
Total
Temp. Range:
C
= -10OC to +70OC
= -40OC to +85OC
Frequency
Tolerance
(in ppm)
I
M = -55OC to +125OC
S
= Customer Specified
10156 - Rev A
E
STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com