Surge Absorbers
7 Initial Characteristices 基本特性 :
项目
测试条件
规格值 Specification
Test Item
Test Method
直流放电电压
DC Spark-Over
VoltageVs(V)
逐渐地增加测量使用直流电压,即可知其开始电压,测
定电流为一毫安与测定时间最大为一秒 (1sec).(1mA)
(Add and measure the DC Voltage gradually Maxto get
the discharge threshold voltage. The measuring current
is 1mA/1 second max.)
依型号而定
(It depands on each part number.)
内绝缘电阻
在规定的设定直流电压下,跨在两端引线,即测量其内
100MΩ或大于 100MΩ
Insulation Resistance 绝缘电阻值.(Measure the insulation resistance of two
(100MΩ min.)
end of leadwire under the specified DC voltage.)
静电电容
使用频率 1KHZ 与小于或等于 6V 直流电压之电源,即
测量其静电电容量 Measure the Electrostatic
1PF 或小于 1PF
Capacitance C(pF)
(1pF max.)
Capacitance under the test condition of 1KHz,DC
6V(max).
8 Enviromental Characteristics(环境试验) :
试验项目
试验方法
性能 Characteristics
Test Item
Test Method
耐寒性(依据 JIS C0020)
放置于-40℃±3℃之环境中 1000 小時后,取出置于常温常湿中 4
满足各个特性之规格值
Within standard
Cold Resistance JIS C0020 小時后,检测直流开始放电电压,绝缘阻抗,静电容量及检查外观.
After -40±3℃(1000hrs) / room temp.,normal humidity(4 hrs)
cycle,measure the properties.
mentioned in Initial
Characteristics.
耐热性(依据 JIS C0021)
放置于 125℃±2℃之环境中 1000 小時后,取出置于常温常湿中 4 满足各个特性之规格值
Heat Resistance JIS C0021 小時后,检测直流开始放电电压,绝缘阻抗,静电容量及检查外观.
After 125±2℃(1000hrs) / room temp.,normal humidity(4 hrs)
cycle,measure the properties.
Within standard
mentioned in Initial
Characteristics.
耐湿性(依据 JIS C0022)
Humidity Resistance JIS
C0020
放置于85℃±2℃ RH85%之环境中1000小時后,取出置于常温常 满足各个特性之规格值
湿中 4 小時后,检测直流开始放电电压,绝缘阻抗,静电容量及
检查外观。
Within standard
mentioned in Initial
Characteristics.
After 85±2℃, 85% RH (1000hrs)/room temp., normal humidity
(4hrs)cycle, measure the properties.
温度周期(依据 JISC0025)
-40℃±3℃(30 分)~(常温 3 分)~125℃±2℃(30 分)为 1 周期,重复
满足各个特性之规格值
Within standard
Temperature Cycle Test (JIS 25 次后,取出置于常温常湿中 4 小時后,检测直流开始放电电压,
C0025)
绝缘阻抗,静电容量及检查外观.
mentioned in Initial
Characteristics.
25 times repetition of cycle -40±3℃ (30 Min.),roon temp., (4
Min.),125±2℃(30 Min.),room temp., normal humidity(4hrs) .
3
HUAAN LIMITED
www.huaandz.com