PCB Layout Guidelines
Figure 29 provides an example of a proper layout for the
FDMF6707B and critical components. All of the high-
current paths, such as VIN, VSWH, VOUT, and GND
copper, should be short and wide for low inductance
and resistance. This technique achieves a more stable
and evenly distributed current flow, along with enhanced
heat radiation and system performance.
boot capacitor (CBOOT) and DrMOS BOOT pin. The
BOOT-to-VSWH loop size, including RBOOT and
CBOOT, should be as small as possible. The boot
resistor may be required when operating near the
maximum rated VIN. The boot resistor is effective at
controlling the high-side MOSFET turn-on slew rate
and VSHW overshoot. RBOOT can improve noise
operating margin in synchronous buck designs that
may have noise issues due to ground bounce or high
positive and negative VSWH ringing. However,
inserting a boot resistance lowers the DrMOS
efficiency. Efficiency versus noise trade-offs must be
considered. RBOOT values from 0.5Ω to 2.0Ω are
typically effective in reducing VSWH overshoot.
The following guidelines are recommendations for the
PCB designer:
1. Input ceramic bypass capacitors must be placed
close to the VIN and PGND pins. This helps reduce
the high-current power loop inductance and the input
current ripple induced by the power MOSFET
switching operation.
8. The VIN and PGND pins handle large current
transients with frequency components greater than
100MHz. If possible, these pins should be connected
directly to the VIN and board GND planes. The use
of thermal relief traces in series with these pins is
discouraged since this adds inductance to the
power path. Added inductance in series with the VIN
or PGND pin degrades system noise immunity by
increasing positive and negative VSWH ringing.
2. The VSWH copper trace serves two purposes. In
addition to being the high-frequency current path
from the DrMOS package to the output inductor, it
also serves as a heat sink for the low-side MOSFET
in the DrMOS package. The trace should be short
and wide enough to present a low-impedance path
for the high-frequency, high-current flow between the
DrMOS and inductor to minimize losses and
temperature rise. Note that the VSWH node is a
high-voltage and high-frequency switching node with
high noise potential. Care should be taken to
minimize coupling to adjacent traces. Since this
copper trace also acts as a heat sink for the lower
FET, balance using the largest area possible to
9. CGND pad and PGND pins should be connected to
the GND plane copper with multiple vias for stable
grounding. Poor grounding can create a noise
transient offset voltage level between CGND and
PGND. This could lead to faulty operation of the gate
driver and MOSFETs.
improve
acceptable noise emission.
DrMOS
cooling
while
maintaining
10.Ringing at the BOOT pin is most effectively
controlled by close placement of the boot capacitor.
Do not add an additional BOOT to the PGND
capacitor: this may lead to excess current flow
through the BOOT diode.
3. An output inductor should be located close to the
FDMF6707B to minimize the power loss due to the
VSWH copper trace. Care should also be taken so
the inductor dissipation does not heat the DrMOS.
11.The SMOD# and DISB# pins have weak internal
pull-up and pull-down current sources, respectively.
These pins should not have any noise filter
capacitors. Do not to float these pins unless
absolutely necessary.
4. PowerTrench® MOSFETs are used in the output
stage. The power MOSFETs are effective at
minimizing ringing due to fast switching. In most
cases, no VSWH snubber is required. If a snubber is
used, it should be placed close to the VSWH and
PGND pins. The resistor and capacitor need to be of
proper size for the power dissipation.
12.Use multiple vias on each copper area to
interconnect top, inner, and bottom layers to help
distribute current flow and heat conduction. Vias
should be relatively large and of reasonably low
inductance. Critical high-frequency components,
such as RBOOT, CBOOT, the RC snubber, and bypass
capacitors should be located as close to the
respective DrMOS module pins as possible on the
top layer of the PCB. If this is not feasible, they
should be connected from the backside through a
network of low-inductance vias.
5. VCIN, VDRV, and BOOT capacitors should be
placed as close as possible to the VCIN to CGND,
VDRV to CGND, and BOOT to PHASE pins to
ensure clean and stable power. Routing width and
length should be considered as well.
6. Include a trace from PHASE to VSWH to improve
noise margin. Keep the trace as short as possible.
7. The layout should include a placeholder to insert a
small-value series boot resistor (RBOOT) between the
© 2011 Fairchild Semiconductor Corporation
FDMF6707B • Rev. 1.0.2
www.fairchildsemi.com
15
5秒后页面跳转
LM317T数据手册解读：产品特性、应用、封装与引脚详解
一文带你了解?DB3二极管好坏判断、参数信息、替代推荐
LM358DR数据手册：引脚说明、电气参数及替换型号推荐
OP07CP数据手册解读：引脚信息、电子参数
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
