SOLID TANTALUM ELECTROLYTIC CAPACITORS
Low Profile
Conformal
Maximum CV
Conformal
F7 2 coated Chip
F7 5 coated Chip
Compliant to the RoHS directive (2002/95/EC).
Specifications
Item
Performance Characteristics
Category
Temperature Range
--55 to +125˚C (Rated temperature : +85˚C)
Capacitance Tolerance ± 20%, ± 10% (at 120Hz)
F72
F75
33 to 68µF
100µF or more
150µF
220µF to 330µF 12%Max.
1000µF
6%Max.
8%Max.
10%Max.
68 to 330µF
470µF
680µF
1000µF
1500µF
2200µF
10%Max.
14%Max.
18%Max.
24%Max.
30%Max.
45%Max.
Dissipation Factor
(120Hz)
30%Max.
33µF
47µF
68µF
100 to 330µF
1000µF
0.90Ω
Less than 150µF 0.22Ω
ESR
0.80Ω
0.75Ω
0.70Ω
0.14Ω
~220µF
~330µF
0.20Ω
0.15Ω
(100kHz)
~470 to 1500µF 0.12Ω
~2200µF 0.07Ω
F72
Type numbering system (Example : 10V 100µF)
After 1 minute's application of rated voltage, leakage current at 20˚C is not
more than 0.01CV or 0.5µA, whichever is greater.
After 1 minute's application of rated voltage, leakage current at 85˚C is not
more than 0.1CV or 5µA, whichever is greater.
After 1 minute's application of derated voltage, leakage current at 125˚C is
not more than 0.125CV or 6.3µA, whichever is greater.
•
•
•
Leakage Current
1
2
3
4
5
6
7
8
9
10 11
Taping code
F 7 2 1 A 1 0 7 M R
(Refer to page 309 for details)
Case code
Capacitance tolerance
Rated capacitance
+15% Max. (at +125˚C)
+10% Max. (at +85˚C)
--10% Max. (at --55˚C)
Capacitance Change
by Temperature
Rated voltage
Series
At 40˚C, 90 to 95% R.H., For 500 hours (No voltage applied)
Capacitance Change • • • • • • Refer to * 1
Damp Heat
Drawing
H
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • Initial specified value or less
(Steady State)
A
B
--
At 55˚C / +125˚C, 30 minutes each, For 5 cycles,
D
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Currentv • • • • • • • • • • Initial specified value or less
Temperature Cycles
L
W
Reflow at 260˚C for 10 seconds, Dipping Flow at 260˚C for 10 seconds
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
Solder electrode
Dimensions
Resistance to
Soldering Heat
(mm)
(D)
Case code
L
W
H
A
±
±
B
±
±
After application of surge in series with a 33Ω resistor at the rate of 30
seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C,
capacitors meet the characteristics requirements listed below.
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
R
7.2
7.2
±
±
0.3 6.0
0.3 6.0
±
±
0.3 1.2
±
0.3 1.3
1.3
0.4 3.8
0.4 3.8
0.6
0.6
(6.2)
(6.2)
M
0.3 2.0MAX.
Surge
D dimension only for reference
F75
Type numbering system (Example : 16V 150µF)
1
2
3
4
5
6
7
8
9
10 11
After 2000 hours' application of rated voltage at 85˚C, or derated voltage at
125˚C, capacitors meet the characteristic requirements listed below.
Capacitance Change • • • • • • Refer to * 1
Dissipation Factor • • • • • • • • • • Initial specified value or less
Leakage Current • • • • • • • • • • • • Initial specified value or less
Taping code
(Refer to page 309 for details)
F 7 5 1 C 1 5 7 M D
Case code
Capacitance tolerance
Rated capacitance
Endurance
Rated voltage
Series
After applying the pressure load of 5N
for 10±1 seconds horizontally to the
center of capacitor side body which has
Drawing
•
5N (0.51kg f)
H
Shear Test
no electrode and has been soldered
For 10 ± 1 seconds
A
beforehand on an aluminum substrate,
there shall be found neither exfoliation
nor its sign at the terminal electrode.
B
D
L
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
W
the pressure strength is applied with
a specified jig at the center of the
substrate so that the substrate may
bend by 1mm as illustrated. Then,
Dimensions
(mm)
(D)
20
R230
Terminal Strength
Case code
L
W
H
A
B
C
D
R
7.1 ± 0.3 3.2 ± 0.3 2.5 ± 0.3 1.3 ± 0.3 3.6 ± 0.6
7.3 ± 0.3 4.3 ± 0.3 2.8 ± 0.3 1.3 ± 0.4 3.9 ± 0.6
7.2 ± 0.3 6.0 ± 0.3 3.5 ± 0.3 1.3 ± 0.4 3.8 ± 0.6
(6.0)
(6.4)
(6.2)
there shall be found no remarkable
abnormality on the capacitor terminals.
45
45
As for the surge and derated voltage at 125 , refer to page 308 for details.
˚C
1 : ∆C/C
*
D dimension only for reference
I t e m
Damp Heat
F72 M
±15
Other
±10
± 5
± 5
± 5
Standard Ratings
F72
Tempereature cycles
Resistance soldering heat
Surge
±15
±15
±15
±15
4
0G
6.3
0J
10
1A
16
1C
V
Code
336
476
686
107
157
227
337
477
687
108
158
Cap.(µF)
033
047
068
100
150
220
330
470
680
1000
1500
R
R
R
±10
Endurance
R
R
R
R
R
R
R
V
4
0G
6.3
0J
10
1A
16
1C
C
F75
Code
Cap. (
µ
F)
R
R
R
R
R
068
100
686
107
157
227
337
477
687
108
158
228
R
C
R
C
D
150
•
C
•
C
D
R
(R)
(M)
(M)
220
C
D
D
R
C
•
330
D
•
C
D
470
D
R
D
•
680
M
R
D
R
1000
1500
2200
R
R
(M)
( ) The series in parentheses are being developed. Please contact to your local
Nichicon sales office when these series are being designed in your application.
CAT.8100Y
5秒后页面跳转
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
PCF8574资料解读：主要参数分析、引脚说明
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
