No.511R / Mar.2005
Engineering Bulletin
Aluminum Electrolytic Capacitors
@Endurance : 85C 2,000 hours
@Solvent-proof type except 350 to 450Vdc
@Pb-free design
SPECIFICATIONS
?
Items
Characteristics
Category
Temperature Range
-
40 to +85C (6.3 to 400Vdc
)
-
25 to +85C (450Vdc
)
Rated Voltage Range 6.3 to 450Vdc
Capacitance Tolerance P20% (M)
(at 20C, 120Hz)
Leakage Current
6.3 to 100Vdc
160 to 450Vdc
Time
I=0.03CV or 4MA, whichever is greater.
I=0.01CV or 3MA, whichever is greater.
After 1minute
CV[1,000 I=0.1CV+40
CV 1,000 I=0.04CV+100
After 5minutes
I=0.03CV+15
I=0.02CV+25
(at 20C)
(at 20C after 1 minute)
(at 20C after 2 minutes)
CV
>
Where, I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc
)
Dissipation Factor
(tane)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V350 to 400V 450V
tanE (Max.)
0.22 0.19 0.16 0.14 0.12 0.10 0.09 0.08
0.20
0.24
0.24
When nominal capacitance exceeds 1,000MF, add 0.02 to the value above for each 1,000MF increase.
(at 20C, 120Hz)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Rated voltage (Vdc)
6.3V 10V 16V 25V 35V 50V 63V 100V 160 to 250V350 to 400V 450V
Z(
-
25C)/Z(+20C)
40C)/Z(+20C)
4
8
3
6
2
4
2
3
2
3
2
3
2
3
2
3
3
4
6
6
16
Z(-
(at 120Hz)
Endurance
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2,000
hours at 85C.
Rated voltage
6.3 to 100Vdc
160 to 400Vdc
450Vdc
Capacitance change
D.F. (tanE)
[P20% of the initial value
[P20% of the initial value
[P20% of the initial value
[150% of the initial specified value [200% of the initial specified value [150% of the initial specified value
[The initial specified value [The initial specified value [The initial specified value
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20C after exposing them for 1,000 hours at 85C without
voltage applied.
Rated voltage
6.3 to 100Vdc
160 to 400Vdc
450Vdc
Capacitance change
D.F. (tanE)
[P20% of the initial value
[P20% of the initial value
[P20% of the initial value
[150% of the initial specified value [200% of the initial specified value [200% of the initial specified value
Leakage current
[The initial specified value
[500% of the initial specified value [500% of the initial specified value
DIMENSIONS [mm]
?
Terminal Code : E
@
Sleeve(Black : PET)
fD
5
6.3
8
10 12.5 16
18
fd 0.5 0.5 0.6 0.6 0.6 0.8 0.8
F
fD'
L'
2.0 2.5 3.5 5.0 5.0 7.5 7.5
FD+0.5max.
L'
15min.
4min.
L+1.5max
(F5 to F10)
(F12.5 to F18)
Vent
(except F5)
Gas escape end seal
PART NUMBERING SYSTEM
?
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E S M E A A A E A A A A A M A A A N
Supplement code
Size code
Capacitance tolerance code
Capacitance code (ex. 0.1MF:R10,10MF:100,100MF:101)
Lead forming·taping code
Terminal code
Voltage code (ex. 6.3V:6R3,35V:350,400V:401)
Series code
Category
Specifications in this bulletin are subject to change without notice.
1
NIPPON CHEMI-CON CORPORATION
1297