LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
long life screw terminals ,105℃
LXA
LXASeries
Long life
Rated voltage range up to 525Vdc
Endurance with ripple current : 5,000 hours at 105 (2,000 hours for 500Vdc & 525Vdc)
High reliability products
・
・
・
・
℃
KMH P270
RoHS Compliant
SPECIFICATIONS
◆
Items
Characteristics
Category
Temperature Range
-
40 to +105 (10 to 100Vdc) -25 to +105 (160 to 525Vdc)
℃ ℃
Rated Voltage Range 10 to 525Vdc
(at 20℃, 120Hz)
(at 20℃ after 5 minutes)
(at 20℃, 120Hz)
Capacitance Tolerance
Leakage Current
-
10 to +50% (T) (10 to 250Vdc)
±20% (M) (350 to 525Vdc)
I=0.02CV or 5mA, whichever is smaller.
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V)
Dissipation Factor
See STANDARD RATINGS (10 to 250Vdc) 0.20max (350 to 525Vdc)
(tan )
δ
℃ ℃
℃ ℃
Capacitance change C(-40 )/C(+20 )≧0.6(10 to 100Vdc) C(-25 )/C(+20 )≧0.7(160 to 250Vdc)
Low Temperature
Characteristics
(at 120Hz)
C(-25 )/C(+20 )≧0.65(350 to 525Vdc)
℃
℃
Insulation Resistance When measured between the terminals that are connected to each other and to the mounting clamp on the insulating sleeve covering
the case by using an insulation resistance meter of 500Vdc, the insulation resistance shall not be less than 100M
Ω
.
Insulation
Withstanding Voltage
When a voltage of 2,000Vac is applied for 1 minute between the terminals that are connected to each other and to the mounting clamp
on the insulating sleeve covering the case, there shall not be electrical damage.
Endurance
The following specifications shall be satisfied when the capacitors are restored to 20 after subjected to DC voltage with the rated
℃
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 5,000 hours (2,000 hours for 500 & 525Vdc products)
at 105 .
℃
Capacitance change
≦±20% of the initial value
D.F. (tanδ)
Leakage current
≦200% of the initial specified value
≦The initial specified value
Shelf Life
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Rated voltage
10 to 250Vdc
≦ 15% of the initial value
±
350 to 525Vdc
Capacitance change
D.F. (tanδ)
≦±20% of the initial value
≦150% of the initial specified value ≦200% of the initial specified value
Leakage current
≦The initial specified value
≦The initial specified value
DIMENSIONS (Screw-Mount) [mm]
Terminal Code : LG
◆
●
●
●
Mounting Clamp Code : B
Mounting Clamp Code : C
360°
3
A±1
W±1
Sleeve (Pb-free PVC : Brown)
45°±5°
6
30°±5°
Vent
8
J
G
1
L+4max.
±
Plastic disk
φD
35
50
63.5
76.2
A
B
W
48
68
80
H
F
φ
E
K
J
F
D
G
φD
10 to 250Vdc 350 to 525Vdc
58
78
90
44
64
76
3.5 12.7
4.5 22.4
4.5 28.0
50
63.5
76.2
89
32.5 37.0 14.0 22.4
38.1 43.5 14.0 28.0
44.5 50.0 14.0 31.5
50.8 56.5 16.0 31.5
~φ63.5
φ76.2
φ89
6
5
5
6
6
4
104.5 90 93.5 4.5 31.5
<Screw specifcations>
Plus hexagon-headed screw :M5×0.8×10
Maximum screw tightening torque :3.23Nm
* The screw and the mounting clamp are separately supplied and not attached to the product.
PART NUMBERING SYSTEM
◆
1
2
3
4
5
6
7
8
9
10
11 12 13
14
15 16 17
18
E L X A A A A L G N A A A M A A A M
Supplement code
Size code
Capacitance tolerance code (ex. M, T)
µ
µ
Capacitance code (ex. 390 F:391, 3,300 F:332)
Mounting clamp code (N, B, C)
Terminal code
Voltage code (ex. 10V:100, 100V:101, 525V:5C1)
Series code
Category
Please refer to "Product code guide (screw-mount terminal type)"
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001N
294