TM
A
L
D
DVANCED
INEAR
EVICES, INC.
®
e
EPAD
EH300/EH300A/EH301/EH301A
EH300/301 EPAD ENERGY HARVESTINGTM MODULES
®
GENERAL DESCRIPTION
BENEFITS
EH300/EH301 Series EPAD® Energy HarvestingTM Modules can
accept energy from many types of electrical energy sources and
store this energy to power conventional 3.3V and 5.0V electrical
circuits and systems. EH300/EH301 Series modules are com-
pletely self-powered and always in the active mode. They are
intended for low power intermittent duty cycle sampled data or
condition-based monitoring/ extreme lifespan applications. These
modules can accept instantaneous input voltages ranging from
0.0V to +/-500VAC or DC, and input currents from 200nAto 400mA
from energy harvesting sources that produce electrical energy in
either a steady or an intermittent and irregular manner with vary-
ing source impedances. EH300/EH301 Series modules condition
the stored energy to provide power at output voltage and current
levels that are within the limits of a particular electronic system
power supply specifications. For example, 1.8V and 3.6V is a useful
voltage range for many types of IC circuits, such as microproces-
sors.
• Eliminates manual and elaborate
system trimming procedures
• Remote controlled automated trimming
• In-System Programming capability
• No external components
• No internal clocking noise source
APPLICATIONS
• Sensor interface circuits
• Transducer biasing circuits
• Capacitive and charge integration circuits
• Biochemical probe interface
• Signal conditioning
• Portable instruments
EH300/EH301 Series modules are designed to continuously and
actively operate to capture, accumulate, and conserve energy from
an external energy source. Each individual EH300/EH301 Series
module is set to operate between two supply voltage thresholds,
MECHANICAL SPECIFICATIONS
+V_low DC and +V_high DC, corresponding to the minimum (V )
L
and maximum (V ) supply voltage values for the intended appli-
H
• Outline Dimensions:
cation. When an energy source starts to inject energy into the
inputs of an EH300/EH301 Series module in the form of electrical
charge impulses, these charge packets are collected, accumulated
and stored onto an internal storage capacitor bank. For most com-
mon energy harvesting applications, the electrical energy charge
packets arrives in the form of input voltage spikes that are uncon-
trolled and unpredictable. Often these cover a wide range of volt-
ages, currents and timing waveforms. EH300/EH301 Series mod-
ules are designed to accommodate such conditions with excep-
tional efficiency and effectiveness. As an example, a EH300 mod-
ule can cycle within 4 minutes at an average input current of 10µA
and within 40 minutes at an average input current of just 1.0µA.
W x L x H : 0.55 in. x 2.00 in. x 0.70 in.
• 4 Mounting Holes: 0.085 in. diameter
• Weight: 0.5 ounce (14 grams) nominal
ORDERING INFORMATION
Part Number
Description
J2
J1
Ground
+Input
V
R (Ready)
EH300
EH300A
4.6 mJ Module / 1.8V to 3.6V operation
30 mJ Module / 1.8V to 3.6V operation
-Input
VP (Output)
+V
EH301
EH301A
8.3 mJ Module / 3.1V to 5.2V operation
55 mJ Module / 3.1V to 5.2V operation
Socket Adapter Cable:
J1: Hirose Socket, 2 Position P/N : DF13-2S
J2: Hirose Socket, 4 Position P/N : DF13-4S
EHJ1C
EHJ2C
6 inch cable / J1connector (Input)
6 inch cable / J2 connector (Output)
Note: EH300A and EH301A are high energy output versions
Rev 2.1 ©2012 Advanced Linear Devices, Inc. 415 Tasman Drive, Sunnyvale, CA 94089-1706 Tel: (408) 747-1155 Fax: (408) 747-1286
www.aldinc.com