DS21455/DS21458
Quad T1/E1/J1 Transceivers
www.maxim-ic.com
GENERAL DESCRIPTION
FEATURES
The DS21455 and DS21458 are quad monolithic
devices featuring independent transceivers that
can be software configured for T1, E1, or J1
operation. Each is composed of a line interface
unit (LIU), framer, HDLC controllers, and a
TDM backplane interface, and is controlled via
an 8-bit parallel port configured for Intel or
Motorola bus operations. The DS21455* is a
direct replacement for the older DS21Q55 quad
MCM device. The DS21458, in a smaller
package (17mm CSBGA) and featuring an
improved controller interface, is software
compatible with the older DS21Q55.
Four Independent Transceivers, Each Having
the Following Features:
CꢀComplete T1 (DS1)/ISDN-PRI/J1
Transceiver Functionality
CꢀComplete E1 (CEPT) PCM-30/ISDN-
PRI Transceiver Functionality
CꢀShort- and Long-Haul Line Interface for
Clock/Data Recovery and Waveshaping
CꢀCMI Coder/Decoder
CꢀCrystal-Less Jitter Attenuator
CꢀFully Independent Transmit and Receive
Functionality
CꢀDual HDLC Controllers
CꢀOn-Chip Programmable BERT Generator
and Detector
*The JTAG function on the DS21455/DS21458 is a single
controller for all four transceivers, unlike the DS21Q55, which has
a JTAG controller-per-transceiver architecture.
CꢀInternal Software-Selectable Receive-
and Transmit-Side Termination Resistors
for 75Ω/100Ω/120Ω T1 and E1
Interfaces
APPLICATIONS
Routers
CꢀDual Two-Frame Elastic-Store Slip
Buffers that can Connect to
Channel Service Units (CSUs)
Data Service Units (DSUs)
Muxes
Asynchronous Backplanes Up to
16.384MHz
Switches
Cꢀ16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz Clock Output Synthesized to
Recovered Network Clock
Channel Banks
T1/E1 Test Equipment
CꢀProgrammable Output Clocks for
Fractional T1, E1, H0, and H12
Applications
ORDERING INFORMATION
PART
DS21455
DS21455N
DS21458
DS21458N
TEMP RANGE PIN-PACKAGE
CꢀInterleaving PCM Bus Operation
Cꢀ8-Bit Parallel Control Port, Multiplexed
or Nonmultiplexed, Intel or Motorola
CꢀIEEE 1149.1 JTAG-Boundary Scan
Cꢀ3.3V Supply with 5V Tolerant Inputs and
Outputs
256 BGA
0°C to +70°C
(27mm x 27mm)
256 BGA
-40°C to +85°C
(27mm x 27mm)
256 CSBGA
0°C to +70°C
(17mm x 17mm)
256 CSBGA
-40°C to +85°C
CꢀDS21455 Directly Replaces DS21Q55
CꢀSignaling System 7 (SS7) Support
CꢀRAI-CI, AIS-CI Support
(17mm x 17mm)
DALLAS is a registered trademark of Dallas Semiconductor Corp.
MAXIM is a registered trademark of Maxim Integrated Products, Inc.
Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device
may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata.
1 of 270
REV: 040804