D2F-T

更新时间： 2024-01-06 19:01:39

品牌	Logo	应用领域
欧姆龙 - OMRON		开关
页数	文件大小	规格书
8页	698K
描述
Snap Action Switch

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

D2F-T 技术参数

是否无铅：	含铅	是否Rohs认证：	符合
生命周期：	Active	包装说明：	ROHS COMPLIANT, PLASTIC, T-1, 2 PIN
针数：	2	Reach Compliance Code：	not_compliant
ECCN代码：	EAR99	HTS代码：	8541.10.00.80
Factory Lead Time：	12 weeks	风险等级：	5.29
Is Samacsys：	N	外壳连接：	ISOLATED
配置：	SINGLE	二极管元件材料：	SILICON
二极管类型：	RECTIFIER DIODE	最大正向电压 (VF)：	1 V
JESD-30 代码：	O-PALF-W2	JESD-609代码：	e3
湿度敏感等级：	1	最大非重复峰值正向电流：	30 A
元件数量：	1	端子数量：	2
最高工作温度：	150 °C	最低工作温度：	-65 °C
最大输出电流：	1 A	封装主体材料：	PLASTIC/EPOXY
封装形状：	ROUND	封装形式：	LONG FORM
峰值回流温度（摄氏度）：	260	认证状态：	Not Qualified
最大重复峰值反向电压：	100 V	最大反向恢复时间：	2 µs
子类别：	Rectifier Diodes	表面贴装：	NO
端子面层：	Matte Tin (Sn)	端子形式：	WIRE
端子位置：	AXIAL	处于峰值回流温度下的最长时间：	40
Base Number Matches：	1

D2F-T 数据手册

Precautions

Be sure to read the precautions and information common to all Snap Action and Detection Switches, contained in the Technical User’s Guide,

“Snap Action Switches, Technical Information” for correct use.

■ Correct Use

■ Cautions

Mounting

Terminal Connection

Turn OFF the power supply before mounting or removing the switch,

wiring the switch, or performing maintenance or inspection. Failure to

do so may result in electric shock or burning.

When soldering a lead wire to the terminal, first insert the lead wire

conductor into the terminal hole and then perform soldering.

Make sure that the capacity of the soldering iron is 30 W maximum

and that the temperature of the soldering tip is approximately 300 °C.

(350 °C maximum.) Complete soldering within 3 s. After soldering,

do not apply external force to the soldered area for about 1 minute.

Mount the switch onto a flat surface. Mounting on an uneven surface

may cause deformation of the switch, resulting in faulty operation or

breakage of the housing.

Allow sufficient insulation distance between terminals, terminal

traces and between terminals and ground.

Using a switch with improper soldering may result in abnormal heat-

ing, possibly resulting in a burn.

Applying the soldering iron for more than 3 s or using an iron that is

rated for more than 30 W may deteriorate the switch characteristics.

Operating Stroke Setting

Take particular care in setting the operating stroke for the pin plunger

models. Make sure that the operating stroke is 70% to 100% of the

rated OT distance. Do not operate the actuator exceeding the OT

distance, otherwise the service life of the switch maybe decreased.

When soldering the lead wire to the PCB terminal, pay careful

attention so that the flux and solder liquid level does not exceed the

PCB level.

Using Microloads

Using a model for ordinary loads to switch microloads may result in

faulty operation. Instead, use the models that are designed for micro-

loads and that operate in the following range;

Operating

range for

general-load

models

Operating range

for micro load

models D2F-01

D2F

Inoperable

range

Current (mA)

However, even when using microload models within the operating

range shown above, if inrush current or inductive voltage spikes

occur when the contact is opened or closed, it may increase contact

wear and so decrease the service life. Therefore, insert a contact

protection circuit where necessary.

Snap Action Switch D2F

1...3 4 567 8

下载PDF

与D2F-T相关器件

型号	品牌	描述	获取价格	数据表
D2FW-G	OMRON	Watertight Snap Action Switch	获取价格
D2FW-G071M	OMRON	Watertight Snap Action Switch	获取价格
D2FW-G072M	OMRON	Watertight Snap Action Switch	获取价格
D2FW-G073M	OMRON	Watertight Snap Action Switch	获取价格
D2FW-G081M	OMRON	Watertight Snap Action Switch	获取价格
D2FW-G082M	OMRON	Watertight Snap Action Switch	获取价格

与D2F-T相关文章

PCF8574资料解读：主要参数分析、引脚说明
2024-05-21

8
AD637数据手册解读：主要特性、引脚及其功能解读、电气参数
2024-05-21

8
ADUM1201资料手册解读：参数分析、引脚说明、应用分析
2024-05-21

11
一文带你了解压敏电阻器在直流电路中的过压保护作用
2024-05-21

6

产品中心

服务支持

精选活动

关于我们

帮助中心

D2F-T

D2F-T 技术参数

D2F-T 数据手册

与D2F-T相关器件

与D2F-T相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

D2F-T

D2F-T 技术参数

D2F-T 数据手册

与D2F-T相关器件

与D2F-T相关文章

您还可以找

您在本页遇到什么问题？