5秒后页面跳转
BU9795AFV-LBE2 PDF预览

BU9795AFV-LBE2

更新时间: 2024-02-03 00:42:55
品牌 Logo 应用领域
罗姆 - ROHM /
页数 文件大小 规格书
29页 862K
描述
Standard LCD Segment Drivers

BU9795AFV-LBE2 数据手册

 浏览型号BU9795AFV-LBE2的Datasheet PDF文件第3页浏览型号BU9795AFV-LBE2的Datasheet PDF文件第4页浏览型号BU9795AFV-LBE2的Datasheet PDF文件第5页浏览型号BU9795AFV-LBE2的Datasheet PDF文件第7页浏览型号BU9795AFV-LBE2的Datasheet PDF文件第8页浏览型号BU9795AFV-LBE2的Datasheet PDF文件第9页 
Daattaasshheeeett  
BU9795AFV-LB  
MAX 108 segments (SEG27×COM4)  
Function Description  
Command and data transfer method  
3-SPI (3wire Serial interface)  
This device is controlled by 3-wire signal (CSB, SCL, and SD).  
First, Interface counter is initialized with CSB=“H", and CSB=“L” makes SD and SCL input enable.  
The protocol of 3-SPI transfer is as follows.  
Each command starts with Command or Data judgment bit (D/C) as MSB data, followed by D6 to D0 during  
CSB =“L”.  
(Internal data is latched at the rising edge of SCL, it is converted to 8bits parallel data at the falling edge of 8th CLK.)  
Command/Data  
Command  
CSB  
SCL  
SD  
D/C D6 D5 D4 D3 D2 D1 D0  
D/C D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6  
D5  
D/C = “H” : Command  
D/C = “L” : Data  
Figure 7. 3-SPI Command/Data transfer format  
Command transfer method  
After CSB=“H””L”, 1st byte is always a command input.  
MSB of the command input data will be judged that the next byte data, it is a command or display data (This bit is  
called  
“command or data judgment bit”).  
When set “command or data judge bit”=‘1’, next byte will be (continuously) command.  
When set “command or data judge bit”=‘0’, next byte data is display data.  
Display Data  
1
Command  
1
Command  
0
Command  
1
Command  
Once it becomes display data transfer condition, it will not be back to command input condition even if D/C=1.  
So if you want to send command data again, please set CSB=“L””H”.  
(CSB “L””H” will cancel data transfer condition.)  
Command transfer is done by 8bits unit, so if CSB=“L””H” with less than 8bits data transfer, command will be  
cancelled.  
It will be able to transfer command with CSB=“L” again.  
In Case Of Command Transfer  
Command  
Command  
CSB  
SCL  
SD  
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
1
Command Cancelled (Less Than 8bits)  
STATUS  
DISCTL Command Transfer  
DISPON Command Transfer  
Figure 8. Command transfer format  
www.rohm.com  
TSZ02201-0P4P0D300510-1-2  
26.Feb.2014 Rev.002  
© 2013 ROHM Co., Ltd. All rights reserved.  
6/26  
TSZ2211115001  

与BU9795AFV-LBE2相关器件

型号 品牌 描述 获取价格 数据表
BU9795AGUM-E2 ROHM Liquid Crystal Driver

获取价格

BU9795AGUW ROHM Standard function Segment Drivers

获取价格

BU9795AGUW-E2 ROHM Standard Segment Drivers

获取价格

BU9795AKS2 ROHM Standard LCD Segment Drivers

获取价格

BU9795AKS2-E2 ROHM Liquid Crystal Driver, 35-Segment, CMOS, PQFP52,

获取价格

BU9795AKV ROHM Standard function Segment Drivers

获取价格