bq24150A
bq24151A
www.ti.com ..................................................................................................................................................................................................... SLUS931–APRIL 2009
Fully Integrated Switch-Mode One-Cell Li-Ion Charger
With Full USB Compliance and USB-OTG Support
1
FEATURES
2
•
Charge Faster than Linear Chargers
–
Output for VBUS: 5.05 V/ 200 mA
•
High-Accuracy Voltage and Current Regulation
•
2 x 2 mm 20-Pin WCSP Package
–
–
–
Input Current Regulation Accuracy: ±5%
(100 mA and 500 mA)
APPLICATIONS
•
•
•
Mobile and Smart Phones
MP3 Players
Handheld Devices
Charge Voltage Regulation Accuracy:
±0.5% (25°C), ±1% (0°C to 125°C)
Charge Current Regulation Accuracy: ±5%
•
High-Efficiency Mini-USB/AC Battery Charger
for Single-Cell Li-Ion and Li-Polymer Battery
Packs
DESCRIPTION
The bq24150A/1A
is
a
compact,
flexible,
high-efficiency, USB-friendly switch-mode charge
management device for single-cell Li-ion and
Li-polymer batteries used in a wide range of portable
applications. The charge parameters can be
programmed through an I2C interface. The
•
•
•
•
20-V Absolute Maximum Input Voltage Rating
6-V Maximum Operating Input Voltage
Built-In Input Current Sensing and Limiting
Integrated Power FETs for Up To 1.25-A
Charge Rate
bq24150A/1A integrates
a
synchronous PWM
controller, power MOSFETs, input current sensing,
high-accuracy current and voltage regulation, and
charge termination, into a small WCSP package.
•
Programmable Charge Parameters through
I2C™ Interface (up to 3.4 Mbps):
–
–
–
–
–
Input Current
The bq24150A/1A charges the battery in three
phases: conditioning, constant current and constant
voltage. The input current is automatically limited to
the value set by the host. Charge is terminated based
on user-selectable minimum current level. A safety
timer with reset control provides a safety backup for
I2C interface. During normal operation, bq24150A/1A
automatically restarts the charge cycle if the battery
voltage falls below an internal threshold and
automatically enters sleep mode or high impedance
mode when the input supply is removed. The charge
status is reported to the host using the I2C interface.
Fast-Charge/Termination Current
Charge Voltage (3.5 V to 4.44 V)
Safety Timer with Reset Control
Termination Enable
•
•
Synchronous Fixed-Frequency PWM
Controller Operating at 3 MHz With 0% to
99.5% Duty Cycle
Robust Protection
–
Reverse Leakage Protection Prevents
Battery Drainage
TYPICAL APPLICATION CIRCUIT
–
–
Thermal Regulation and Protection
Input/Output Overvoltage Protection
L
1.0 mH
O
R
SNS
V
BUS
VBUS
SW
C
O
C
IN
C
U1
bq24150A/1A
BOOT
•
•
Status Output for Charging and Faults
10
mF
1 mF
10nF
PACK+
+
PMID
BOOT
PGND
Automatic High Impedance Mode for Low
Power Consumption
C
IN
0.1 mF
VAUX
4.7 mF
CSIN
CSOUT
AUXPWR
VREF
10 kW
10 kW
2
I
C BUS
PACK-
10 kW
SCL
SCL
SDA
STAT
•
•
•
•
USB Friendly Boot-Up Sequence
SDA
STAT
OTG
C
AUXPWR
Automatic Charging – bq24150A
OTG
C
1
mF
VREF
10 kW
1
mF
HOST
Automatic High Impedance Mode – bq24151A
Boost Mode Operation for USB OTG:
–
Input Voltage Range (from Battery): 2.5 V to
4.5 V
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
I2C is a trademark of Philips Electronics.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated