AFCT-5710APZ

更新时间： 2024-02-18 02:21:59

品牌	Logo	应用领域
安华高科 - AVAGO		光纤放大器以太网通信
页数	文件大小	规格书
19页	248K
描述
Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI for Gigabit Ethernet

阅读下载

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

AFCT-5710APZ 技术参数

是否Rohs认证：	符合	生命周期：	Transferred
Reach Compliance Code：	compliant	ECCN代码：	5A991.B.5.A
HTS代码：	8517.62.00.50	风险等级：	5.17
Is Samacsys：	N	主体宽度：	16.25 mm
主体高度：	12.1 mm	主体长度或直径：	42.3 mm
内置特性：	AMPLIFIER	通信标准：	GBE, GR-468
连接类型：	LC CONNECTOR	数据速率（发送）：	1250 Mbps
发射极/检测器类型：	LASER	光纤设备类型：	TRANSCEIVER
光纤类型：	50, 62.5, MMF, SMF	JESD-609代码：	e4
安装特点：	PANEL MOUNT	最高工作温度：	85 °C
最低工作温度：	-10 °C	最大工作波长：	1355 nm
最小工作波长：	1270 nm	标称工作波长：	1313 nm
标称光功率输出：	0.237 mW	最小回损：	12 dB
灵敏度：	-19 dBm	子类别：	Fiber Optic Transceivers
最大供电电压：	3.47 V	最小供电电压：	3.14 V
标称供电电压：	3.3 V	表面贴装：	NO
端子面层：	Gold (Au)	Base Number Matches：	1

AFCT-5710APZ 数据手册

Table 2. Pin description

Engagement

Order(insertion)

Name

Function/Description

Notes

VeeT

Transmitter Ground

TX Fault

TX Disable

MOD-DEF2

MOD-DEF1

MOD-DEF0

Rate Selection

LOS

Transmitter Fault Indication

Transmitter Disable - Module disables on high or open

Module Deﬁnition 2 - Two wire serial ID interface

Module Deﬁnition 1 - Two wire serial ID interface

Module Deﬁnition 0 - Grounded in module

Not Connected

Loss of Signal

VeeR

Receiver Ground

Notes:

VeeR

Receiver Ground

VeeR

Receiver Ground

RD-

Inverse Received Data Out

Received Data Out

RD+

VeeR

Reciver Ground

VccR

Receiver Power -3.3 V 5%

Transmitter Power -3.3 V 5%

Transmitter Ground

VccT

VeeT

TD+

Transmitter Data In

TD-

Inverse Transmitter Data In

Transmitter Ground

VeeT

1. TX Fault is an open collector/drain output which should be pulled up externally with a 4.7KΩ – 10 KΩ resistor on the host board to a supply

<VccT+0.3 V or VccR+0.3 V. When high, this output indicates a laser fault of some kind. Low indicates normal operation. In the low state, the

output will be pulled to < 0.8 V.

2. TX disable input is used to shut down the laser output per the state table below. It is pulled up within the module with a 4.7-10 KΩ resistor.

Low (0 – 0.8 V): Transmitter on

Between (0.8 V and 2.0 V): Undeﬁned

High (2.0 – 3.465 V): Transmitter Disabled

Open: Transmitter Disabled

3. Mod-Def 0,1,2. These are the module deﬁnition pins. They should be pulled up with a 4.7-10 KΩ resistor on the host board to a supply less

than VccT +0.3 V or VccR+0.3 V.

Mod-Def 0 is grounded by the module to indicate that the module is present

Mod-Def 1 is clock line of two wire serial interface for optional serial ID

Mod-Def 2 is data line of two wire serial interface for optional serial ID

4. LOS (Loss of Signal) is an open collector/drain output which should be pulled up externally with a 4.7 KΩ – 10 KΩ resistor on the host board

to a supply < VccT,R+0.3 V. When high, this output indicates the received optical power is below the worst case receiver sensitivity (as deﬁned

by the standard in use). Low indicates normal operation. In the low state, the output will be pulled to < 0.8 V.

5. RD-/+: These are the diﬀerential receiver outputs. They are AC coupled 100 Ω diﬀerential lines which should be terminated with 100 Ω

diﬀerential at the user SERDES. The AC coupling is done inside the module and is thus not required on the host board. The voltage swing on

these lines must be between 370 and 2000 mV diﬀerential (185 – 1000 mV single ended) according to the MSA. Typically it will be 1500mv

diﬀerential.

6. VccR and VccT are the receiver and transmitter power supplies. They are deﬁned as 3.135 – 3.465 V at the SFP connector pin. The in-rush

current will typically be no more than 30 mA above steady state supply current after 500 nanoseconds.

7. TD-/+: These are the diﬀerential transmitter inputs. They are AC coupled diﬀerential lines with 100 Ω diﬀerential termination inside the

module. The AC coupling is done inside the module and is thus not required on the host board. The inputs will accept diﬀerential swings of

500 – 2400 mV (250 – 1200 mV single ended). However, the applicable recommended diﬀerential voltage swing is found in Table 5.

1...4 5 678 9 10...19

下载PDF

与AFCT-5710APZ相关器件

型号	品牌	描述	获取价格	数据表
AFCT-5710APZ-AL1	AVAGO	FIBER OPTIC TRANSCEIVER, 1270-1335nm, 1250Mbps(Tx), 1250Mbps(Rx), BOARD/PANEL MOUNT, LC CO	获取价格
AFCT-5710LZ	AVAGO	Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI	获取价格
AFCT-5710PZ	AVAGO	Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI	获取价格
AFCT-5710xxZ	BOARDCOM	Single-Mode SFP Optical Transceivers with Optional DMI for Gigabit Ethernet and Fibre Chan	获取价格
AFCT-5710xxZ	AVAGO	Single-Mode SFP Optical Transceivers	获取价格
AFCT-5710Z	AVAGO	Families of Single-Mode Small Form Factor Pluggable Optical Transceivers with Optional DMI	获取价格

与AFCT-5710APZ相关文章

MAX6675资料手册参数详解、引脚配置说明
2024-05-13

5
LM258引脚图及功能介绍、主要参数分析
2024-05-13

3
CD4052资料手册参数详解、引脚配置说明
2024-05-13

5
一文带你了解TPS5430资料手册分析：参数介绍、引脚配置说明
2024-05-13

6

产品中心

服务支持

精选活动

关于我们

帮助中心

AFCT-5710APZ

AFCT-5710APZ 技术参数

AFCT-5710APZ 数据手册

与AFCT-5710APZ相关器件

与AFCT-5710APZ相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

AFCT-5710APZ

AFCT-5710APZ 技术参数

AFCT-5710APZ 数据手册

与AFCT-5710APZ相关器件

与AFCT-5710APZ相关文章

您还可以找

您在本页遇到什么问题？