AD8343
Table I. Typical AC Performance
(VS = 5.0 V, TA = 25ꢂC; See Figure 24 and Tables III Through V.)
Input 1 dB
Compression Point
(dBm)
Input Frequency
(MHz)
Output Frequency Conversion Gain SSB Noise Figure Input IP3
(MHz)
(dB)
(dB)
(dBm)
RECEIVER CHARACTERISTICS
400
900
1900
2400
2400
70
5.6
3.6
7.1
6.8
5.4
10.5
11.4
14.1
15.3
16.2
20.5
19.4
16.5
14.5
16.5
3.3
3.6
2.8
2.1
2.2
170
170
170
425
TRANSMITTER CHARACTERISTICS
150
150
900
1900
7.5
0.25
17.9
16.0
18.1
13.4
1.9
0.8
Table II. Typical Isolation Performance
(VS = 5.0 V, TA = 25ꢂC; See Figure 24 and Tables III Through V.)
Input Frequency
(MHz)
Output Frequency LO to Output
2 ꢃ LO to Output 3 ꢃ LO to Output Input to Output
(MHz)
Leakage (dBm)
Leakage (dBm)
Leakage (dBm)
Leakage (dBm)
RECEIVER CHARACTERISTICS
400
70
–40.1
–44.4
–65.6
–66.7
–51.1
–51.0
–35.5
–38.3
–44.4
–49.4
–44.0
< –75.0
–73.3
< –75.0
< –75.0
–62.4
–56.9
–65.7
–73.7
–52.3
900
170
170
170
425
1900
2400
2400
TRANSMITTER CHARACTERISTICS
150
150
900
1900
–27.6
< –75 dBm
< –75 dBm
< –75 dBm
< –75 dBm
< –75 dBm
–35.3
–69.7
NOTE: Low-side LO injection used for typical performance.
ABSOLUTE MAXIMUM RATINGS1
PIN CONFIGURATION
VPOS Quiescent Voltage . . . . . . . . . . . . . . . . . . . . . . . . 5.5 V
OUTP, OUTM Quiescent Voltage . . . . . . . . . . . . . . . . 5.5 V
INPP, INPM Voltage Differential . . . . . . . . . . . . . . . 500 mV
Internal Power Dissipation (TSSOP)2 . . . . . . . . . . . . 320 mW
COMM
INPP
1
2
3
4
5
6
7
14 COMM
13
12
11
10
9
OUTP
OUTM
COMM
LOIP
INPM
θ
JA (TSSOP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125°C/W
AD8343
TOP VIEW
(Not to Scale)
DCPL
VPOS
PWDN
COMM
Maximum Junction Temperature . . . . . . . . . . . . . . . . . 125°C
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . . 300°C
LOIM
8
COMM
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may effect device reliability.
2A portion of the device power is dissipated by the external bias resistors R3 and R4.
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
AD8343ARU
RU-14
AD8343ARU-REEL
AD8343ARU-REEL7
AD8343-EVAL
–40°C to +85°C
14-Lead Plastic TSSOP 13" Tape and Reel
7" Tape and Reel
Evaluation Board
–3–
REV. 0