AD693
Model
AD693AD
Typ
Conditions
Min
Max
Units
AUXILIARY AMPLIFIER
Common-Mode Range
Input Offset Voltage
0
+VOP – 4 V6
±200
+20
V
±50
+5
+0.5
90
µV
nA
nA
dB
dB
mA
%
Input Bias Current
Input Offset Current
Common-Mode Rejection
Power Supply Rejection
Output Current Range
Output Current Error
±3.0
105
Pin IX OUT
Pin VX – Pin IX
+0.01
+5
±0.005
TEMPERATURE RANGE
Case Operating14
Storage
TMIN to TMAX
–40
–65
+85
+150
°C
°C
NOTES
1 Total error can be significantly reduced (typically less than 0.1%) by trimming the zero current. The remaining unadjusted error sources are transconductance and
nonlinearity.
2 The AD693 is tested as a loop powered device with the signal amp, V/I converter, voltage reference, and application voltages operating together. Specifications are
valid for preset spans and spans between 30 mV and 60 mV.
3 Error from ideal output assuming a perfect 100 Ω RTD at 0 and +100°C.
4 Refer to the Error Analysis to calculate zero current error for input spans less than 30 mV.
5 By forcing the differential signal amplifier input sufficiently negative the 7 µA zero current can always be achieved.
6 The operational voltage (VOP) is the voltage directly across the AD693 (Pin 10 to 6 in two-wire mode, Pin 9 to 6 in local power mode). For example, VOP = VS
–
(ILOOP × RL) in two-wire mode (refer to Figure 10).
7Bias currents are not symmetrical with input signal level and flow out of the input pins. The input bias current of the inverting input increases with input signal volt-
age, see Figure 2.
8 Nonlinearity is defined as the deviation of the output from a straight line connecting the endpoints as the input is swept over a 30 mV and 60 mV input span.
9 Specifications for the individual functional blocks are components of error that contribute to, and that are included in, the Loop Powered Operation specifications.
10 Includes error contributions of V/I converter and Application Voltages.
11 Changes in the reference output voltage due to load will affect the Zero Current. A 1% change in the voltage reference output will result in an error of 1% in the
value of the Zero Current.
12 If not used for external excitation, the reference should be loaded by approximately 1 mA (6.2 kΩ to common).
13 In the loop powered mode up to 5 mA can be drawn from the reference, however, the lower limit of the output span will be increased accordingly. 3.5 mA is the
maximum current the reference can source while still maintaining a 4 mA zero.
14 The AD693 is tested with a pass transistor so TA TC.
Specifications subject to change without notice.
Specifications shown in boldface are tested on all production units at final electrical test. Results from those tests are used to calculate outgoing quality levels. All min
and max specifications are guaranteed, although only those shown in boldface are tested on all production units.
AD693 PIN CONFIGURATION
(AD, AQ, AE Packages)
ABSOLUTE MAXIMUM RATINGS
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +36 V
Reverse Loop Current . . . . . . . . . . . . . . . . . . . . . . . . . 200 mA
Signal Amp Input Range . . . . . . . . . . . . . . . . . . –0.3 V to VOP
Reference Short Circuit to Common . . . . . . . . . . . . Indefinite
Auxiliary Amp Input Voltage Range . . . . . . . . . . 0.3 V to VOP
Auxiliary Amp Current Output . . . . . . . . . . . . . . . . . . . 10 mA
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature, 10 sec Soldering . . . . . . . . . . . . . +300°C
Max Junction Temperature . . . . . . . . . . . . . . . . . . . . . +150°C
ORDERING GUIDE
Package
Description
Package
Option
Model
AD693AD
AD693AQ
AD693AE
Ceramic Side-Brazed DIP
Cerdip
Leadless Ceramic Chip
Carrier (LCCC)
D-20
Q-20
E-20A
Functional Diagram
REV. A
–3–
5秒后页面跳转
一文带你解读74HC244资料手册：特性、应用场景、封装方式、引脚配置说明、电气参数、推荐替代型号
AD623资料手册解读：特性、应用、封装、引脚功能及电气参数
RT9193资料手册解读：RT9193引脚功能、电气参数、替换型号推荐
VIPER22A的资料手册解读、引脚参数说明、代换型号推荐
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
