AAT3200
OmniPower™ LDO Linear Regulator
If large output current steps are required by an
application, then an increased value for COUT
should be considered. The amount of capacitance
needed can be calculated from the step size of the
change in the output load current expected and the
voltage excursion that the load can tolerate.
Applications Information
To assure the maximum possible performance is
obtained from the AAT3200, please refer to the fol-
lowing application recommendations.
The total output capacitance required can be cal-
culated using the following formula:
Input Capacitor
Typically, a 1µF or larger capacitor is recommended
for CIN in most applications. A CIN capacitor is not
required for basic LDO regulator operation.
However, if the AAT3200 is physically located any
distance more than one or two centimeters from the
input power source, a CIN capacitor will be needed
for stable operation. CIN should be located as
closely to the device VIN pin as practically possible.
CIN values greater than 1µF will offer superior input
line transient response and will assist in maximizing
the highest possible power supply ripple rejection.
∆I
∆V
COUT
=
× 15µF
Where:
∆I = maximum step in output current
∆V = maximum excursion in voltage that the load
can tolerate
Note that use of this equation results in capacitor
values approximately two to four times the typical
value needed for an AAT3200 at room temperature.
The increased capacitor value is recommended if
tight output tolerances must be maintained over
extreme operating conditions and maximum opera-
tional temperature excursions. If tantalum or alu-
minum electrolytic capacitors are used, the capaci-
tor value should be increased to compensate for the
substantial ESR inherent to these capacitor types.
Ceramic, tantalum, or aluminum electrolytic capaci-
tors may be selected for CIN. There is no specific
capacitor equivalent series resistance (ESR)
requirement for CIN. For 150mA to 250mA LDO reg-
ulator output operation, ceramic capacitors are rec-
ommended for CIN due to their inherent capability
over tantalum capacitors to withstand input current
surges from low impedance sources such as bat-
teries in portable devices.
Output Capacitor
Capacitor Characteristics
For proper load voltage regulation and operational
stability, a capacitor is required between pins VOUT
and GND. The COUT capacitor connection to the
LDO regulator ground pin should be made as direct
as practically possible for maximum device per-
formance. The AAT3200 has been specifically
designed to function with very low ESR ceramic
capacitors. Although the device is intended to oper-
ate with low ESR capacitors, it is stable over a very
wide range of capacitor ESR, thus it will also work
with some higher ESR tantalum or aluminum elec-
trolytic capacitors. However, for best performance,
ceramic capacitors are recommended.
Ceramic composition capacitors are highly recom-
mended over all other types of capacitors for use
with the AAT3200. Ceramic capacitors offer many
advantages over their tantalum and aluminum elec-
trolytic counterparts. A ceramic capacitor typically
has very low ESR, is lower cost, has a smaller PCB
footprint, and is non-polarized. Line and load tran-
sient response of the LDO regulator is improved by
using low ESR ceramic capacitors. Since ceramic
capacitors are non-polarized, they are less prone
to damage if incorrectly connected.
Equivalent Series Resistance: ESR is a very
important characteristic to consider when selecting
a capacitor. ESR is the internal series resistance
associated with a capacitor that includes lead
The value of COUT typically ranges from 0.47µF to
10µF; however, 1µF is sufficient for most operating
conditions.
3200.2005.04.1.1
9
5秒后页面跳转
CP2102资料手册解读：CP2102引脚说明、关键参数分析
资料手册解读：UC3842参数和管脚说明
一文带你了解无源晶振的负载电容为何要加两颗谐振电容CL1和CL2
玻璃管保险丝与陶瓷管保险丝：区别与替代性探讨
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
