Model Selection Guide
Input
Current (mA)
Output
Fuse Rating
Slow-Blow
(mA)
Voltage (VDC)
Model
Reflected
Ripple
Efficiency
(%, Typ)
Voltage Current
(VDC) (mA, Max) (mA, Min)
Current
Number
Nominal
Range
Full-Load No-Load
Current
(mA, Typ)
A201R
A202R
A203R
A204R
A205R
A211R
A212R
A213R
A214R
A215R
A221R
A222R
A223R
A224R
A225R
A231R
A232R
A233R
A234R
A235R
5
5
5
5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
4.5 - 5.5
800
730
690
740
740
330
295
265
280
280
163
135
135
135
135
83
80
80
80
80
80
40
40
40
40
40
20
20
20
20
20
10
10
10
10
10
80
80
80
80
80
30
30
30
30
30
15
15
15
15
15
10
10
10
10
10
5.0
400
165
133
83
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
50
54
57
53
51
50
56
62
59
59
51
61
61
61
61
50
59
59
51
51
1,500
1,500
1,500
1,500
1,500
700
700
700
700
700
350
350
350
350
350
135
135
135
12.0
15.0
12.0
15.0
5.0
12.0
15.0
12.0
15.0
5.0
12.0
15.0
12.0
15.0
5.0
12.0
15.0
12.0
15.0
5
66
12
12
12
12
12
24
24
24
24
24
48
48
48
48
48
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
10.8 - 13.2
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
21.6 - 26.4
43.2 - 52.8
43.2 - 52.8
43.2 - 52.8
43.2 - 52.8
43.2 - 52.8
400
165
133
83
66
400
165
133
83
66
400
165
133
83
70
70
80
80
135
135
66
Notes:
1. When measuring output ripple, it is recommended that an external 0.33 μF ceramic Derating Curve
capacitor be placed from the +Vout pin to the -Vout pin for single output units and from
each output to common for dual output units. For noise sensitive applications, the use
of 1.5 μF capacitors will reduce the output ripple.
2. Transient recovery is measured to within a 1% error band for a load step change of
50% to 100%.
3. Operation at no-load will not damage these units. However, they may not meet all
specifications.
4. Dual output units may be connected to provide a 24 VDC or 30 VDC output. To do this,
connect the load across the positive (+Vout) and negative (-Vout) outputs and float the
output common.
5. The converter should be connected to a low ac-impedance source.An input source with
a highly inductive impedance may affect the stability of the converter. In applications
where the converter output loading is high and input power is supplied over long lines,
it may be necessary to use a capacitor on the input to insure start-up.
In this case, it is recommended that a low ESR (ESR <1.0Ω at 100 kHz) capacitor be
mounted close to the converter. For 5V input units a 2.2 μF is recommended, for 12V
input units, a 1.0 μF; and for 24V & 48V units a 0.47 μF.
6. It is recommended that a fuse be used on the input of a power supply for protection.
See the table above for the correct rating.
Mechanical Dimensions
Pin Connections
Pin
Single
+Vin
NC
Dual
+Vin
1, 24
2, 23
3, 22
10, 15
11, 14
12, 13
-Vout
NC
Common
Common
+Vout
-Vin
-Vout
+Vout
-Vin
NC: No Connection
Capacitive Load
Single Output
470 μF Max
Dual Output
220 μF Max
Mechanical Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = 0.01 ( 0.25)
• Leads are tin plated for improved solderability.
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
■
TEL: (781) 344-8226
■
FAX: (781) 344-8481
■
E-Mail: sales@micropowerdirect.com