5秒后页面跳转
A1221EUA-T PDF预览

A1221EUA-T

更新时间: 2024-01-21 02:24:23
品牌 Logo 应用领域
急速微 - ALLEGRO 传感器换能器磁场传感器信息通信管理
页数 文件大小 规格书
13页 281K
描述
Chopper Stabilized Precision Hall Effect Latches

A1221EUA-T 技术参数

是否无铅: 不含铅是否Rohs认证: 符合
生命周期:Active包装说明:SIP3,.03,50
Reach Compliance Code:compliant风险等级:0.67
Is Samacsys:N其他特性:REVERSE BATTERY PROTECTION, SHORT-CIRCUIT PROTECTION
主体宽度:1.52 mm主体高度:5.26 mm
主体长度或直径:4.09 mm滞后:10 mT
JESD-609代码:e3最大磁场范围:9 mT
最小磁场范围:-9 mT安装特点:THROUGH HOLE MOUNT
端子数量:3最大工作电流:4 mA
最高工作温度:150 °C最低工作温度:-40 °C
输出电路类型:SINGLE-ENDED最大输出电流:25 mA
输出范围:30-60mA输出类型:ANALOG CURRENT
封装主体材料:PLASTIC/EPOXY封装等效代码:SIP3,.03,50
封装形状/形式:RECTANGULAR电源:3/24 V
传感器/换能器类型:MAGNETIC FIELD SENSOR,HALL EFFECT子类别:Other Sensors/Transducers
最大供电电压:24 V最小供电电压:3 V
表面贴装:NO技术:BICMOS
端子面层:Matte Tin (Sn)端接类型:SOLDER
Base Number Matches:1

A1221EUA-T 数据手册

 浏览型号A1221EUA-T的Datasheet PDF文件第6页浏览型号A1221EUA-T的Datasheet PDF文件第7页浏览型号A1221EUA-T的Datasheet PDF文件第8页浏览型号A1221EUA-T的Datasheet PDF文件第10页浏览型号A1221EUA-T的Datasheet PDF文件第11页浏览型号A1221EUA-T的Datasheet PDF文件第12页 
A1220, A1221  
and A1222  
Chopper Stabilized Precision Hall Effect Latches  
Functional Description  
Operation  
Applications  
The output of these devices switches low (turns on) when a mag-  
netic field perpendicular to the Hall element exceeds the operate  
point threshold, BOP (see panel A of figure 1). After turn-on, the  
output voltage is VOUT(SAT). The output transistor is capable of  
sinking current up to the short circuit current limit, IOM, which is  
a minimum of 30 mA. When the magnetic field is reduced below  
the release point, BRP, the device output goes high (turns off).  
The difference in the magnetic operate and release points is the  
hysteresis, BHYS, of the device. This built-in hysteresis allows  
clean switching of the output even in the presence of external  
mechanical vibration and electrical noise.  
It is strongly recommended that an external bypass capacitor be  
connected (in close proximity to the Hall element) between the  
supply and ground of the device to reduce both external noise  
and noise generated by the chopper stabilization technique. As is  
shown in panel B of figure 1, a 0.1 μF capacitor is typical.  
Extensive applications information for Hall effect devices is  
available in:  
Hall-Effect IC Applications Guide, Application Note 27701  
Guidelines for Designing Subassemblies Using Hall-Effect  
Devices, Application Note 27703.1  
Removal of the magnetic field will leave the device output  
latched on if the last crossed switchpoint is BOP, or latched off if  
the last crossed switch point is BRP.  
Soldering Methods for Allegros Products – SMT and Through-  
Hole, Application Note 26009  
Powering-on the device in the hysteresis range (less than BOP and  
higher than BRP) will give an indeterminate output state. The cor-  
All are provided in Allegro Electronic Data Book, AMS-702, and  
rect state is attained after the first excursion beyond BOP or BRP  
.
the Allegro Web site, www.allegromicro.com.  
VS  
V+  
VCC  
VCC  
RL  
A122x  
CBYP  
VOUT  
0.1 μF  
Output  
GND  
VOUT(SAT)  
B+  
0
B–  
0
BHYS  
(A)  
(B)  
Figure 1. Switching behavior of latches. In panel A, on the horizontal axis, the B+ direction indicates increasing south polarity magnetic field strength,  
and the B– direction indicates decreasing south polarity field strength (including the case of increasing north polarity). This behavior can be exhibited  
when using a circuit such as that shown in panel B.  
Allegro MicroSystems, Inc.  
115 Northeast Cutoff  
9
Worcester, Massachusetts 01615-0036 U.S.A.  
1.508.853.5000; www.allegromicro.com  

与A1221EUA-T相关器件

型号 品牌 描述 获取价格 数据表
A1221LLHLT-T ALLEGRO Chopper Stabilized Precision Hall Effect Latches

获取价格

A1221LLHLT-T2 ALLEGRO Chopper Stabilized Precision Hall Effect Latches

获取价格

A1221LLHLX-T ALLEGRO Chopper Stabilized Precision Hall Effect Latches

获取价格

A1221LUA-T ALLEGRO Chopper Stabilized Precision Hall Effect Latches

获取价格

A1222 ALLEGRO Chopper Stabilized Precision Hall Effect Latches

获取价格

A1-2226SCC HRS Wire Terminal

获取价格